An experimental investigation was conducted on the internal flowfield of a simulated smooth-wall turbine blade cooling passage. The square cross-sectioned passage was manufactured from quartz for optical accessibility. Velocity measurements were taken using Particle Image Velocimetry for both heated and non-heated cases. Thin film resistive heaters on all four exterior walls of the passage allowed heat to be added to the coolant flow without obstructing laser access. Under the same conditions, an infrared detector with associated optics collected wall temperature data for use in calculating local Nusselt number. The test section was operated with radial outward flow and at values of Reynolds number and Rotation number typical of a small turbine blade. The density ratio was 0.27. Velocity data for the non-heated case document the evolution of the Coriolis-induced double vortex. The vortex has the effect of disproportionately increasing the leading side boundary layer thickness. Also, the streamwise component of the Coriolis acceleration creates a considerably thinned side wall boundary layer. Additionally, these data reveal a highly unsteady, turbulent flowfield in the cooling passage. Velocity data for the heated case show a strongly distorted streamwise profile indicative of a buoyancy effect on the leading side. The Coriolis vortex is the mechanism for the accumulation of stagnant flow on the leading side of the passage. Heat transfer data show a maximum factor of two difference in the Nusselt number from trailing side to leading side. A first-order estimate of this heat transfer disparity based on the measured boundary layer edge velocity yields approximately the same factor of two. A momentum integral model was developed for data interpretation, which accounts for coriolis and buoyancy effects. Calculated streamwise profiles and secondary flows match the experimental data well. The model, the velocity data, and the heat transfer data combine to strongly suggest the presence of separated flow on the leading wall starting at about five hydraulic diameters from the channel inlet for the conditions studied.
Skip Nav Destination
Article navigation
October 1999
Research Papers
1998 Heat Transfer Committee Best Paper Award: Complementary Velocity and Heat Transfer Measurements in a Rotating Cooling Passage With Smooth Walls
J. P. Bons,
J. P. Bons
Department of Aeronautics and Astronautics, Air Force Institute of Technology, Wright-Patterson AFB, OH 45433
Search for other works by this author on:
J. L. Kerrebrock
J. L. Kerrebrock
Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA 02139
Search for other works by this author on:
J. P. Bons
Department of Aeronautics and Astronautics, Air Force Institute of Technology, Wright-Patterson AFB, OH 45433
J. L. Kerrebrock
Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA 02139
J. Turbomach. Oct 1999, 121(4): 651-662 (12 pages)
Published Online: October 1, 1999
Article history
Received:
February 1, 1998
Online:
January 29, 2008
Citation
Bons, J. P., and Kerrebrock, J. L. (October 1, 1999). "1998 Heat Transfer Committee Best Paper Award: Complementary Velocity and Heat Transfer Measurements in a Rotating Cooling Passage With Smooth Walls." ASME. J. Turbomach. October 1999; 121(4): 651–662. https://doi.org/10.1115/1.2836717
Download citation file:
Get Email Alerts
Evaluating Thin-Film Thermocouple Performance on Additively Manufactured Turbine Airfoils
J. Turbomach (July 2025)
Thermohydraulic Performance and Flow Structures of Diamond Pyramid Arrays
J. Turbomach (July 2025)
Related Articles
Latticework (Vortex) Cooling Effectiveness: Rotating Channel Experiments
J. Turbomach (July,2005)
Coupling of Volumetric Flowfield and Surface Effectiveness Measurements for Flat-Plate Film Cooling With Cylindrical Holes Using Tomographic Particle Image Velocimetry and Pressure-Sensitive Paint
J. Thermal Sci. Eng. Appl (June,2023)
High-Resolution Measurements of Local Heat Transfer Coefficients From Discrete Hole Film Cooling
J. Turbomach (October,2001)
A Detailed Analysis of Film Cooling Physics: Part III— Streamwise Injection With Shaped Holes
J. Turbomach (January,2000)
Related Proceedings Papers
Related Chapters
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Insulating Properties of W-Doped Ga2O3 Films Grown on Si Substrate for Low-K Applications
International Conference on Advanced Computer Theory and Engineering, 4th (ICACTE 2011)
Extended Surfaces
Thermal Management of Microelectronic Equipment, Second Edition