The unified approach based upon the Reduced Reynolds technique is applied to develop a deterministic transient mixed lubrication line contact model. This model is used in spur gear applications to comprehensively show effects of roughness, working conditions, i.e., rotational speeds and loads on pressure ripples and severity of asperity contacts. Results show effects of the speed, the load, as well as the RMS value are coupled which makes it difficult to evaluate lubrication states by only considering one variable. Considering the Ree-Eyring non-Newtonian behavior could alleviate pressure ripples significantly, compared with the Newtonian fluid assumption. Small RMS values of surfaces, which could be achieved by superfinish techniques, would be desirable when evaluating gear tooth surface contact performances.
Issue Section:
Elastohydrodynamic Lubrication
References
1.
Snidle
, R. W.
, and Evans
, H. P.
, 2009, “Some Aspects of Gear Tribology
,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci.
, 223
(1
), pp. 103
–113
.2.
Zhu
, D.
, and Wang
, Q. J.
, 2011, “Elastohydrodynamic Lubrication: A Gateway to Interfacial Mechanics—Review and Prospect
,” ASME J. Tribol.
, 133
(4
), pp. 041001
–14
.3.
Lugt
, P. M.
, and Morales-Espejel
, G. E.
, 2011, “A Review of Elasto-Hydrodynamic Lubrication Theory
,” Tribol. Trans.
, 54
(3
), pp. 470
–496
.4.
Dowson
, D.
, and Higginson
, G. R.
, 1977, Elasto-Hydrodynamic Lubrication
, Pergamon Press
, New York
.5.
Evans
, H. P.
, and Snidle
, R. W.
, 2009, “The Future of Engineering Tribology in Concentrated Contacts
,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci.
, 223
(12
), pp. 2939
–2948
.6.
Chang
, L.
, Webster
, M. N.
, and Jackson
, A.
, 1993, “On the Pressure Rippling and Roughness Deformation in Elastohydrodynamic Lubrication of Rough Surfaces
,” ASME J. Tribol.
, 115
(3
), pp. 439
–444
.7.
Patching
, M. J.
, Evans
, H. P.
, and Snidle
, R. W.
, 1996, “Micro-Ehl Analysis of Ground and Superfinished Steel Discs Used to Simulate Gear Tooth Contacts
,” Tribol. Trans.
, 39
(3
), pp. 595
–602
.8.
Venner
, C. H.
, and Lubrecht
, A. A.
, 1994, “Transient Analysis of Surface Features in an Ehl Line Contact in the Case of Sliding
,” ASME J. Tribol.
, 116
(2
), pp. 186
–193
.9.
Johnson
, K. L.
, Greenwood
, J. A.
, and Poon
, S. Y.
, 1972, “Simple Theory of Asperity Contact in Elastohydrodynamic Lubrication
,” Wear
, 19
(1
), pp. 91
–108
.10.
Patir
, N.
, and Cheng
, H. S.
, 1978, “An Average Flow Model for Determining Effects of Three-Dimensional Roughness of Partial Hydrodynamic Lubrication
,” ASME J. Lubr. Technol.
, 100
, pp. 12
–17
.11.
Zhao
, J. X.
, Sadeghi
, F.
, and Hoeprich
, M. H.
, 2001, “Analysis of Ehl Circular Contact Start Up: Part I - Mixed Contact Model with Pressure and Film Thickness Results
,” ASME J. Tribol.
, 123
(1
), pp. 67
–74
.12.
Hu
, Y. Z.
, and Zhu
, D.
, 2000, “A Full Numerical Solution to the Mixed Lubrication in Point Contacts
,” ASME J. Tribol.
, 122
(1
), pp. 1
–9
.13.
Holmes
, M. J. A.
, Evans
, H. P.
, Hughes
, T. G.
, and Snidle
, R. W.
, 2003, “Transient Elastohydrodynamic Point Contact Analysis Using a New Coupled Differential Deflection Method. Part 1: Theory and Validation
,” Proc. Inst. Mech. Eng, Part J: J. Eng. Tribol.
, 217
(4
), pp. 289
–303
.14.
Holmes
, M. J. A.
, Evans
, H. P.
, and Snidle
, R. W.
, 2005, “Analysis of Mixed Lubrication Effects in Simulated Gear Tooth Contacts
,” ASME J. Tribol.
, 127
(1
), pp. 61
–69
.15.
Wang
, K. L.
, and Cheng
, H. S.
, 1981, “A Numerical Solution to the Dynamic Load, Film Thickness, and Surface Temperatures in Spur Gears, Part I - Analysis
,” ASME J. Mech. Des.
, 103
, pp. 177
–187
.16.
Larsson
, R.
, 1997, “Transient Non-Newtonian Elastohydrodynamic Lubrication Analysis of an Involute Spur Gear
,” Wear
, 207
(1–2
), pp. 67
–73
.17.
Hua
, D. Y.
, and Khonsari
, M. M.
, 1995, “Application of Transient Elastohydrodynamic Lubrication Analysis for Gear Transmissions
,” Tribol. Trans.
, 38
(4
), pp. 905
–913
.18.
Akbarzadeh
, S.
, and Khonsari
, M. M.
, 2008, “Thermoelastohydrodynamic Analysis of Spur Gears with Consideration of Surface Roughness
,” Tribol. Lett.
, 32
(2
), pp. 129
–141
.19.
Li
, S.
, and Kahraman
, A.
, 2010, “A Transient Mixed Elastohydrodynamic Lubrication Model for Spur Gear Pairs
,” ASME J. Tribol.
, 132
(1
), pp. 011501
-9
.20.
Conry
, T. F.
, Wang
, S.
, and Cusano
, C.
, 1987, “A Reynolds-Eyring Equation for Elastohydrodynamic Lubrication in Line Contacts
,” ASME J. Tribol.
, 109
(4
), pp. 648
–658
.21.
Dowson
, D.
, 1998, “Modelling of Elastohydrodynamic Lubrication of Real Solids by Real Lubricants
,” Meccanica
, 33
(1
), pp. 47
–58
.22.
Jacod
, B.
, 2002, “Friction in Elasto-Hydrodynamic Lubrication
,” Ph. D. thesis, University of Twente, Enschede, The Netherlands.23.
Venner
, C. H.
, Ten Napel
, W. E.
, and Bosma
, R.
, 1990, “Advanced Multilevel Solution of the Ehl Line Contact Problem
,” ASME J. Tribol.
, 112
(3
), pp. 426
–431
.24.
Moes
, H.
, 1992, “Optimum Similarity Analysis with Applications to Elastohydrodynamic Lubrication
,” Wear
, 159
(1
), pp. 57
–66
.25.
Wang
, Y.
, Li
, H.
, Tong
, J.
, and Yang
, P.
, 2004, “Transient Thermoelastohydrodynamic Lubrication Analysis of an Involute Spur Gear
,” Tribol. Int.
, 37
(10
), pp. 773
–782
.26.
Venner
, C. H.
, 1991, “Multigrid Solution of the Ehl Line and Point Contact Problems
,” Ph. D. thesis, University of Twente, The Netherlands.27.
Chang
, L.
, and Zhao
, W.
, 1995, “Fundamental Differences between Newtonian and Non-Newtonian Micro-Ehl Results
,” ASME J. Tribol.
, 117
(1
), pp. 29
–35
.28.
Cioc
, C.
, Cioc
, S.
, Moraru
, L.
, Kahraman
, A.
, and Keith
, T. G.
, 2002, “A Deterministic Elastohydrodynamic Lubrication Model of High-Speed Rotorcraft Transmission Components
,” Tribol. Trans.
, 45
(4
), pp. 556
–562
.Copyright © 2012
by American Society of Mechanical Engineers
You do not currently have access to this content.
