Multistage centrifugal pumps and compressors are among the most widely used pieces of rotating machinery in industry. A typical application demands the arrangement of several impellers or wheels mounted on a shaft that spins within a stationary case. Annular seals are the most common sealing devices used in this type of machinery. The annular seal design affects both (i) machinery performance in terms of energy conversion efficiency, and (ii) stability due to the interaction within the rotor and the stator through the fluid flow within the seals. Traditionally, the “bulk-flow” theory due to Hirs (ASME J. Lubrication Technol., pp. 137–146) has been used to estimate annular seals leakage and dynamic coefficients. To predict the flow behavior through the seal, this theory relies on empirical friction factor correlations. While leakage is well predicted, the dynamic coefficients are not. The discrepancy is attributed to the friction factor model. Several experiments have produced seal leakage data indicating that friction factor increases as the seal clearance is increased, contradicting predictions based on Moody’s pipe-friction model. A Computational Fluid Dynamics (CFD) commercial code was used to simulate flat-plate-channel-flow experimental tests of water flowing with deliberately roughened surfaces, showing an increase of friction factor with clearance increase. The higher friction factor characteristics of these deliberately roughened surfaces are governed by their ability to develop a high static pressure in the trailing face of each roughness cavity, while the wall shear stresses on the smooth land play a secondary role. In a certain Reynolds number range, the maximum friction factor observed on a specific roughness pattern size is independent of the actual clearance, which we have referred to as the friction-factor-to-clearance indifference behavior. This phenomenon is found to be related to the roughness cavity size and its length-to-clearance ratio.

Issue Section:
Technical Papers
Keywords:
friction, seals (stoppers), rough surfaces, computational fluid dynamics, pumps, channel flow
Topics:
Clearances (Engineering), Friction, Reynolds number, Flow (Dynamics), Surface roughness, Turbulence
1.
Lomakin, A., 1958, “Calculation of Critical Numbers of Revolutions and the Conditions Necessary for Dynamic Stability of Rotors in High-Pressure Hydraulic Machines when Taking into Account Forces Originating in Sealing,” Power and Mechanical Engineering, (in Russian); Energomashinostroerie, 14(4), pp. 1–5.
2.
Hirs
,
G.
,
1973
, “
A Bulk-flow Theory for Turbulence in Lubricant Films
,”
ASME J. Lubr. Technol.
,
95
, pp.
137
–
146
.
3.
Von Pragenau, G. L., 1982, “Damping seals for turbomachinery,” NASA Technical Paper No. 1987.
4.
Childs
,
D. W.
, and
Fayolle
,
P.
,
1999
, “
Test Results for Liquid ‘Damper’ Seals using a Round-hole Roughness Pattern for the Stators
,”
ASME J. Tribol.
,
121
, pp.
42
–
49
.
5.
DeOtte, R., Morrison, G. L., Nava, D. L., and Hess, J. C., 1994, “A Study of Friction Factors in Channel Flow between Plates with Highly Roughened Surfaces,” Fluid Machinery 1994, U. S. Rohatgi and A. Ogut, eds., ASME, New York, FED-Vol. 195.
6.
Ha
,
T. W.
, and
Childs
,
D. W.
,
1992
, “
Friction-factor Data for Flat-plate Tests of Smooth and Honeycomb Surfaces
,”
ASME J. Tribol.
,
114
, pp.
722
–
730
.
7.
Al-Qutub
,
A.
,
Elrod
,
D.
, and
Coleman
,
H.
,
2000
, “
A New Friction Factor Model and Entrance Loss Coefficient for Honeycomb Annular Gas Seals
,”
ASME J. Tribol.
,
122
, pp.
622
–
627
.
8.
Athavale, M. M., Hendricks, R. C., and Steinetz, B. M., 1995, “Numerical Simulation of Flow in a Whirling Annular Seal and Comparison with Experiments,” NASA Technical Memorandum 106961.
9.
Morrison
,
G. L.
,
Johnson
,
M. C.
, and
Tatterson
,
G. B.
,
1991
, “
Three-dimensional Laser Anemometer Measurements in an Annular Seal
,”
ASME J. Tribol.
,
113
, pp.
421
–
427
.
10.
Schramm, V., Willenborg, K., Kim S., and Wittig, S., 2000, “Influence of a Honeycomb Facing on the Flow Through a Stepped Labyrinth Seal,” in Proceedings of the ASME TURBOEXPO 2000, 2000-GT-0291.
11.
Chochua, G., Shyy, W., and Moore, J., 2001, “Thermophysical Modeling for Honeycomb-stator Gas Annular Seal,” 35th AIAA Thermophysics Conference, AIAA 2001-2757.
12.
Chien
,
K.-Y.
,
1982
, “
Predictions of Channel and Boundary-layer Flows with a low-Reynolds-number Turbulence Model
,”
AIAA J.
,
20
, pp.
33
–
38
.
13.
Nava, D. L., 1993, “Observations of Friction Factors for Various Roughness Patterns in Channel Flow,” Turbomachinery Laboratory Report No. TL-Seal-13-95, Texas A&M University, College Station.
14.
Hess, J. C., 1993, “Dynamic Pressure Response of Water Flow between Closely Spaced Roughened Flat plates,” Texas A&M University, College Station.
15.
Ethembabaogˇlu
,
S.
,
1978
, “
Some Characteristics of Unstable Flow past Slots
,”
J. Hydraul. Div., Am. Soc. Civ. Eng.
,
HY5
(
13738
), pp.
649
–
666
.
16.
Sato, H., 1989, “An Equation of State for the Thermodynamic Properties of Water in the Liquid phase including the Metastable state,” in Proceedings of the 11th International Conference on the Properties of Water and Steam, M. Pı´chal and O. Sˇifner eds., Hemisphere Publishing Corporation, Prague, Czechoslovakia. pp. 48–55.
17.
Watson, J. T. R., Basu R. S., and Sengers, J. V., 1979, “An Improved Equation for the Viscosity of Water and Steam,” in Proceedings of the 9th International Conference on the Properties of Steam, J. Straub and K. Scheffler eds., Pergamon Press, pp. 336–343, Technische Universita¨t Mu¨nchen, Federal Republic of Germany.
18.
Patankar
,
S. V.
,
Liu
,
C. H.
, and
Sparrow
,
E. M.
,
1977
, “
Fully Developed Flow and Heat Transfer in Ducts having Streamwise-Periodic Variations of Cross-sectional Area
,”
J. Heat Transfer
,
99
, p.
180
180
.
19.
Pope, S. B., 2000, Turbulent Flows, Cambridge University Press, United Kingdom, Chap. 11, pp. 457–462.
20.
Chen, C. J., and Jaw, S. Y., 1998, Fundamentals of Turbulence Modeling, Taylor & Francis, Washington, D.C.
21.
Patel
,
V. C.
,
Rodi
,
W.
, and
Scheuerer
,
G.
,
1984
, “
Turbulence Models for Near-wall and Low Reynolds Number Flows: A Review
,”
AIAA J.
,
23
(
9
), pp.
1308
–
1319
.
22.
Patel
,
V. C.
, and
Chen
,
H. C.
,
1987
, “
Turbulent Wake on a Flat Plate
,”
AIAA J.
,
25
(
8
), pp.
1078
–
1085
.
23.
Chen
,
H. C.
, and
Patel
,
V. C.
,
1988
, “
Near-wall Turbulence Models for Complex Flows Including Separation
,”
AIAA J.
,
26
(
6
), pp.
641
–
648
.
24.
Wolfshtein
,
M.
,
1969
, “
The Velocity and Temperature Distribution in One-Dimensional Flow with Turbulence Augmentation and Pressure Gradient
,”
Int. J. Heat Mass Transfer
,
12
, pp.
301
–
318
.
25.
Villasmil, L. A., 2002, “Understanding the Friction Factor Behavior in Liquid Annular Seals with Deliberately Roughened Surfaces, a CFD Approach,” Texas A&M University, College Station.
26.
Villasmil, L. A., Chen, H. C., and Childs, D. W., “Evaluation of Near-wall Turbulence Models for Liquid Annular Seals with Roughened Walls,” AIAA-2003-3741, 33rd AIAA Fluid Dynamics Conference.
27.
Lobanoff, V., and Ross, R., 1992, “Centrifugal Pumps: Design and Application,” Gulf Publishing Co., Houston, Chap. 10, pp. 151.
28.
FLUENT 5 User’s Guide, No. 1999-04-07, Fluent Incorporated, Lebanon, New Hampshire.
Copyright © 2005
 by ASME
You do not currently have access to this content.