A new method has been developed to directly measure valve train friction as a function of crank angle using specially designed timing belt pulley torque transducers fitted to the inlet and exhaust camshafts of a single-cylinder gasoline engine. Simultaneous and instantaneous friction torque of both the inlet and exhaust camshafts at any engine speed can be measured, with no apparent detrimental effect of timing belt loading on the output reading. Experiments are reported for valve train friction at a range of motored engine operating conditions with different lubricant formulations, with and without a friction modifier. These are compared with the predictions of an existing valve train friction model based upon elastohydrodynamic lubrication theory. Measured friction decreased with increasing engine speed but increased with increasing oil temperature and the fuel economy benefit of friction modifiers was observed. The model yielded similar magnitudes of friction at medium engine speeds and above but predicted much lower friction with high oil temperatures at low speed. Comparison of theory and experiments also suggests that some oil may leak from hydraulic lash adjusters during the cam event with a consequent reduction in geometric torque.

Issue Section:
Technical Papers
Keywords:
sliding friction, rolling friction, valves, internal combustion engines, mechanical variables measurement, lubrication, torque
Topics:
Camshafts, Engines, Friction, Torque, Trains, Valves, Temperature, Lubricants, Transducers, Bearings
1.
Parker, D. A., and Adams, D. R., 1982, “Friction Losses in the Reciprocating Internal Combustion Engine,” Tribology—Key to the Efficient Engine, Instn. Mech. Engrs., Conf. Pub. 1982-1, London, Paper C5/82, pp. 31–39.
2.
Hoshi
,
M.
,
1984
, “
Reducing Friction losses in Automobile Engines
,”
Tribol. Int.
,
17
, pp.
185
–
189
.
3.
Rezrka, S. F., and Henein, N. A., 1984, “A New Approach to Evaluate Instan-taneous Friction and Its Components in Internal Combustion Engines,” SAE Paper 840179.
4.
Dowson, D., Harrison, P., and Taylor, C. M., 1986, “The Lubrication of Automotive Cams and Followers,” Mechanisms and Surface Distress, Proc. 12th Leeds-Lyon Symposium on Tribology, Butterworths, London, pp. 305–322.
5.
Taylor, C. M., 1991, “Valve Train Lubrication Analysis,” Vehicle Tribology, Proc. 17th Leeds-Lyon Symposium on Tribology, Elsevier, Amsterdam, pp. 119–131.
6.
Ball, W. F., Jackson, N. S., Pilley, A. D., and Porter, B. C., 1986, “The Friction of a 1.6 Liter Automotive Engine-Gasoline and Diesel,” SAE Paper 860418.
7.
Baniasad, M. S. and Emes, M. R., 1998, “Design and Development of Method of Valve-Train Friction Measurement,” SAE Paper 980572.
8.
Dowson, D., Taylor, C. M., and Zhu, G., 1989, “An Experimental Study of the Tribology of a Cam and Flat-faced follower,” 2nd Int. Conf., Combustion Engines—Reduction of Friction and Wear, Instn. Mech. Engrs. Conf. Pub., London, Paper C375/025, pp. 97–108.
9.
Ball, A. D., 1988, “A Tribological Study of the Design and Performance of Automotive Cams,” Ph.D. thesis, Dept. of Mechanical Engineering, University of Leeds, UK, pgs. 250.
10.
Zhu, G., and Taylor, C. M., 2001, “Tribological Analysis and Design of a Modern Automobile Cam and Follower,” Engineering Research Series 7, Instn. Mech. Engrs., Professional Engineering Publishing, London.
11.
Dickenson, A. N., 2000, “Engine Friction Modelling Considering Lubricant Tribological Characteristics,” Ph.D. thesis, School of Mechanical Engineering, University of Leeds, UK, pgs. 232.
12.
Dyson, A., and Naylor, H., 1960, “Application of the Flash Temperature Concept to Cam and Tappet Wear Problems,” Proc. Instn. Mech. Engrs., Automotive Div., 8, pp. 255–280.
13.
Hertz
,
H.
,
1882
, “
On the Contact of Elastic Solids
,”
J. Reine Angew. Math.
,
92
, pp.
156
–
171
.
14.
Dowson, D., and Higginson, G. R., 1977, Elastrohydrodynamic Lubrication, SI Edition, Pergamon Press, Oxford.
15.
Dowson, D., and Toyoda, S., 1979, “A Central Film Thickness Formula for Elastrohydrodynamic Line Contacts,” Elastohydrodynamics and Related Topics, Proc. 5th Leeds-Lyon Symposium on Tribology, Mechanical Engineering Publications, London, pp. 60–65.
Copyright © 2003
 by ASME
You do not currently have access to this content.