Miniature devices including MEMS and the head disk interface in magnetic storage often include very smooth surfaces, typically having root-mean-square roughness, σ of the order of 10 nm or less. When such smooth surfaces contact, or come into proximity of each other, either in dry or wet environments, then strong intermolecular (adhesive) forces may arise. Such strong intermolecular forces may result in unacceptable and possibly catastrophic adhesion, stiction, friction and wear. In the present paper, a model termed sub-boundary lubrication (SBL) adhesion model is used to calculate the adhesion forces, and an elastic-plastic model is used to calculate the contact forces at typical MEMS interfaces. Several levels of surface roughness are investigated representing polished and as-deposited polysilicon films that are typically found in MEMS. The SBL adhesion model reveals the significance of the surface roughness on the adhesion and pull-off forces as the surfaces become smoother. The validity of using the SBL adhesion model to estimate the pull-off forces in miniature systems is further supported by direct comparison with experimental pull-off force measurements performed on silicon and gold interfaces. Finally, the significance of the interfacial forces as relate to the reliability of MEMS interfaces is discussed.

Issue Section:
Technical Papers
Keywords:
adhesion, surface topography, mechanical contact, interface phenomena, intermolecular forces, lubrication, elastoplasticity, micromechanical devices, silicon, gold
Topics:
Adhesion, Lubrication, Microelectromechanical systems, Silicon, Surface roughness, Polysilicon, Stress, Adhesives, Intermolecular forces
1.
Tian
,
H.
, and
Matsudaira
,
T.
,
1993
, “
The Role of Relative Humidity, Surface Roughness and Liquid Buildup on Static Friction Behavior of the Head/Disk Interface
,”
ASME J. Tribol.
,
115
, pp.
28
–
35
.
2.
Kaneko
,
R.
, 1991, “Microtribology Related to MEMS-Concept, Measurement, Applications,” IEEE, Proceedings of Micro Electro Mechanical Systems, 91, pp. 1–8.
3.
Komvopoulos
,
K.
,
1996
, “
Surface Engineering and Microtribology for Microelectromechanical Systems
,”
Wear
,
200
(
1–2
), pp.
305
–
327
.
4.
Maboudian
,
R.
, and
Howe
,
R. T.
,
1997
, “
Critical Review: Adhesion in Surface Micro electro mechanical Structures
,”
J. Vac. Sci. Technol. B
,
15
(
1
), pp.
1
–
20
.
5.
Torii, A., Sasaki, M., Hane, K., and Okuma, S., 1993, “Adhesive Force on the Microstructures Measured by the Atomic Force Microscope,” MEMS ’93, Proc. An Investigation of Micro Structures, Sensors Actuators, Machines and Systems, IEEE, pp. 111–116.
6.
Jennings, J. M., and Phinney, L. M., 2000, “Effects of Temperature on Stiction in MEMS Structures,” Proc. of SPIE: MEMS Reliability for Critical Applications, 4180(6), Russell A. Lawton, ed., pp. 66–75.
7.
Israelachvili, J. N., 1991, Intermolecular and Surface Forces, Academic Press, 2nd ed., San Diego.
8.
Stanley
,
H. M.
,
Etsion
,
I.
, and
Bogy
,
D. B.
,
1990
, “
Adhesion of Contacting Rough Surfaces in the Presence of Sub-Boundary Lubrication
,”
ASME J. Tribol.
,
112
, pp.
98
–
104
.
9.
Greenwood
,
J. A.
, and
Williamson
,
J. P. B.
,
1966
, “
Contact of Nominally Flat Surfaces
,”
Proc. R. Soc. London, Ser. A
,
295
, pp.
300
–
319
.
10.
Polycarpou
,
A. A.
, and
Etsion
,
I.
,
1998
, “
Static Friction of Contacting Real Surfaces in the Presence of Sub-Boundary Lubrication
,”
ASME J. Tribol.
,
120
, pp.
296
–
303
.
11.
Polycarpou
,
A. A.
, and
Etsion
,
I.
,
1998
, “
Comparison of the Static Friction Sub-Boundary Lubrication Model with Experimental Measurements on Thin Film Disks
,”
STLE Tribol. Trans.
,
41
(
2
), pp.
217
–
224
.
12.
Tanner, D. M., Miller, W. M., Eaton, W. P., Irwin, L. W., Peterson, K. A., Dugger, M. T., Senft, D. C., Smith, N. F., Tangyunyong, P., and Miller, S. L., 1998, “The Effect of Frequency on the Lifetime of a Surface Micromachined Microengine Driving a Load,” IEEE 36th Annual Reliability Physics Symposium Proceedings, pp. 26–35.
13.
Polycarpou, A. A., 2002, “Modeling Adhesive Forces for Ultra Low Flying Head Disk Interfaces,” in Nanotribology: Critical Assessment and Research Needs, S. M. Hsu, ed., Kluwer Academic Publishers.
14.
Ando
,
Y.
,
2000
, “
Wear Tests and Pull-Off Force Measurements of Single Asperities by Using Parallel Leaf Springs Installed on an Atomic Force Microscope
,”
ASME J. Tribol.
,
122
, pp.
639
–
645
.
15.
Polycarpou, A. A., and Suh, A., 2001, “A Model for Adhesive Forces in Miniature Systems,” in Fundamentals of Tribology and Bridging the Gap Between Macro- and Micro/Nanoscales, B. Bhushan, ed., Kluwer Academic Publishers.
16.
Chang
,
W. R.
,
Etsion
,
I.
, and
Bogy
,
D. B.
,
1987
, “
An Elastic-Plastic Model for the Contact of Rough Surfaces
,”
ASME J. Tribol.
,
109
, pp.
257
–
263
.
17.
Johnson
,
K. L.
,
Kendall
,
K.
, and
Roberts
,
A. D.
,
1971
, “
Surface Energy and the Contact of Elastic Solids
,”
Proc. R. Soc. London, Ser. A
,
324
, pp.
301
–
313
.
18.
Derjaguin
,
B. V.
,
Muller
,
V. M.
, and
Toporov
,
Y. P.
,
1975
, “
Effect of Contact Deformations on the Adhesion of Particles
,”
J. Colloid Interface Sci.
,
53
, pp.
314
–
326
.
19.
McCool
,
J. I.
,
1987
, “
Relating Profile Instrument Measurements of the Functional Performance of Rough Surfaces
,”
ASME J. Tribol.
,
109
, pp.
264
–
279
.
20.
Bhushan, B., 1999, Handbook of Micro/Nanotribology, 2nd ed., CRC Press.
21.
Brandes, E. A., 1983, Smithells Metals Reference Book, 6th ed., Butterworth and Co.
Copyright © 2003
 by ASME
You do not currently have access to this content.