This paper reports an investigation of the use of off-axis carbon fibers in the all-carbon spar cap of a 37-m wind turbine rotor blade to induce twist-flap coupling. Many studies have been published on the structure of wind turbine rotor blades incorporating off-axis fibers; none has studied optimizing the blade structure simultaneously considering the angle of off-axis material, the fraction of off-axis material, constraints on cross-fiber and in-plane shear strength, constraints on tip deflection, and blade cost. A parametric study has been conducted varying the angle of off-axis fibers from 5° to 25° and varying the volume fraction of off-axis fibers in the spar cap from 10% to 90%. In all configurations, the remainder of the spar cap material is 0° carbon fiber. The spar cap thickness has been adjusted in each blade to simultaneously minimize the weight of carbon material, and hence the blade cost, while satisfying constraints on carbon fiber strain and tip deflection. The study also examines the cross-fiber strain and stress and the in-plane shear stress in the 0° and off-axis carbon layers. The conclusion of this study is that the optimal angle for most cost-effectively achieving twist-flap coupling—considering constraints on fiber strain, cross-fiber strength, in-plane shear strength, and tip deflection—is closer to 7.5° than the 20° that has frequently been reported by prior researchers. As much as 90% of the spar cap carbon fibers can be rotated to 7.5° off-axis before in-plane shear strength is exceeded.
Skip Nav Destination
e-mail: kyle.wetzel@kwetzel.com
Article navigation
November 2005
Research Papers
Utility Scale Twist-Flap Coupled Blade Design
Kyle K. Wetzel
e-mail: kyle.wetzel@kwetzel.com
Kyle K. Wetzel
Wetzel Engineering, Inc.
, P.O. Box 4153, Lawrence, Kansas 66046-1153
Search for other works by this author on:
Kyle K. Wetzel
Wetzel Engineering, Inc.
, P.O. Box 4153, Lawrence, Kansas 66046-1153e-mail: kyle.wetzel@kwetzel.com
J. Sol. Energy Eng. Nov 2005, 127(4): 529-537 (9 pages)
Published Online: June 23, 2005
Article history
Received:
February 2, 2005
Revised:
June 21, 2005
Accepted:
June 23, 2005
Citation
Wetzel, K. K. (June 23, 2005). "Utility Scale Twist-Flap Coupled Blade Design." ASME. J. Sol. Energy Eng. November 2005; 127(4): 529–537. https://doi.org/10.1115/1.2037089
Download citation file:
Get Email Alerts
Mass Flow Control Strategy for Maximum Energy Extraction in Thermal Energy Storage Tanks
J. Sol. Energy Eng (December 2025)
Exergy Optimization of a Hybrid Multi-Evaporative Desalination Plant Powered by Solar and Geothermal Energy
J. Sol. Energy Eng (June 2025)
Correlation for Maximum Heat Transfer Between Fluidized Bed and Its Wall and Application to Solar Power Plants
J. Sol. Energy Eng (June 2025)
Related Articles
3D Woven Carbon/Glass Hybrid Spar Cap for Wind Turbine Rotor Blade
J. Sol. Energy Eng (November,2006)
Alternative Composite Materials for Megawatt-Scale Wind Turbine Blades: Design Considerations and Recommended Testing
J. Sol. Energy Eng (November,2003)
New Fatigue Data for Wind Turbine Blade Materials
J. Sol. Energy Eng (November,2003)
Delamination at Thick Ply Drops in Carbon and Glass Fiber Laminates Under Fatigue Loading
J. Sol. Energy Eng (August,2008)
Related Chapters
Performance and Mechanical Equipment Standards
Handbook for Cogeneration and Combined Cycle Power Plants, Second Edition
Introduction
Turbine Aerodynamics: Axial-Flow and Radial-Flow Turbine Design and Analysis
Regression Based Neural Network for Studying the Vibration Control of the Rotor Blade for Micro-Unmanned Helicopter
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3