Abstract

Low-alloy steels are extensively used in pressure boundary components of nuclear power plants. The structural integrity of the components made of low-alloy steels can be evaluated by the flaw evaluation procedure provided by Section XI of the ASME Boiler and Pressure Vessel Code. According to the Code, the stress intensity factor range ΔK can be used to determine the fatigue crack growth rates of the material. However, it has been reported that the fatigue crack growth rate under severe reversing loads is also strongly influenced by crack closure behavior. This paper discusses the relation between applied stresses and the fatigue crack growth rate for cracks in low-alloy steels exposed to air. Compressive-tensile cyclic loadings are applied to center-notched plates to obtain the fatigue crack growth curves. The test data demonstrate that effective stress intensity factor range predicted by our closure model described the crack growth property more accurately. A comparison among crack closure models indicates that our crack closure model is suitable to predict the crack growth rates when low constraint conditions are assumed at the crack tip due to severe reversing loads.

Issue Section:
Materials and Fabrication
Topics:
Fatigue cracks, Fracture (Materials), Stress, Steel

References

1.
Anderson
,
T. L.
,
2005
, “
Fracture Mechanics: Fundamentals and Applications
,” 3rd ed.,
CRC Press
,
Cambridge, UK
, Chap.
10
.
2.
Eason
,
E. D.
,
Gilman
,
J. D.
,
Jones
,
D. P.
, and
Andrew
,
S. P.
,
1992
, “
Technical Basis for a Revised Fatigue Crack Growth Rate Reference Curve for Ferritic Steels in Air
,”
ASME J. Pressure Vessel Technol.
,
114
(
1
), pp.
80
–
86
.10.1115/1.2929016
3.
ASME
,
2017
,
ASME B&PV Code Section XI, Rules for Inservice Inspection of Nuclear Power Plant Components
,
American Society of Mechanical Engineers
,
New York
.
4.
Maierhofer
,
J.
,
Kolitsch
,
S.
,
Pippan
,
R.
,
Gänser
,
H.-P.
,
Madia
,
M.
, and
Zerbst
,
U.
,
2018
, “
The Cyclic R-Curve—Determination, Problems, Limitations and Application
,”
Eng. Fract. Mech.
,
198
, pp.
45
–
64
.10.1016/j.engfracmech.2017.09.032
5.
Kurihara
,
M.
,
Katoh
,
A.
, and
Kawahara
,
M.
,
1986
, “
Analysis on Fatigue Crack Growth Rates Under a Wide Range of Stress Ratios
,”
ASME J. Pressure Vessel Technol.
,
108
(
2
), pp.
209
–
213
.10.1115/1.3264771
6.
Bloom
,
J. M.
,
1994
, “
An Approach to Account for Negative R-Ratio Effects in Fatigue Crack Growth Calculations for Pressure Vessels Based on Crack Closure Concepts
,”
ASME J. Pressure Vessel Technol.
,
116
(
1
), pp.
30
–
35
.10.1115/1.2929555
7.
Schijve
,
J.
,
1981
, “
Some Formulas for the Crack Opening Stress Level
,”
Eng. Fract. Mech.
,
14
(
3
), pp.
461
–
465
.10.1016/0013-7944(81)90034-5
8.
Newman
,
J. J.
,
1984
, “
A Crack Opening Stress Equation for Fatigue Crack Growth
,”
Int. J. Fract.
,
24
(
4
), pp.
R131
–
R135
.10.1007/BF00020751
9.
Bloom
,
J. M.
, and
Hechmer
,
J. L.
,
1997
, “
High Stress Crack Growth—Part II: Predictive Methodology Using a Crack Closure Model
,”
Fatigue and Fracture: Proceedings of the 1997 ASME Pressure Vessels and Piping Conference
, Vol.
350
, Orlando, FL, July 27–31, pp.
351
–
357
.
10.
Hechmer
,
J. L.
, and
Bloom
,
J. M.
,
1997
, “
High Stress Crack Growth—Part I: Testing Program and Data Assessment
,”
Fatigue and Fracture: Proceedings of the 1997 ASME Pressure Vessels and Piping Conference
, Vol.
350
, Orlando, FL, July 27–31, pp.
337
–
345
.
11.
ASME
,
2011
, “
American Society of Mechanical Engineers (ASME) Codes and New and Revised ASME Code Cases; Final Rule
,” American Society of Mechanical Engineers,
New York
, Document No.
2011-14652
.10.1115/2011-14652https://www.federalregister.gov/documents/2012/01/23/2012-1212/american-society-of-mechanical-engineers-asme-codes-and-new-and-revised-asme-code-cases-corrections
12.
The Nuclear Regulatory Commission,
2018
, “
Codes and Standards
,” The Office of the Federal Register, Washington, DC, Standard No.
10 CFR 50.55a
. https://www.nrc.gov/reading-rm/doc-collections/cfr/part050/part050-0055a.html
13.
ASME
,
2017
,
ASME B&PV Code Section II, Part D Properties (Customary)
,
American Society of Mechanical Engineers
,
New York
.
14.
Zonfrillo
,
G.
,
2017
, “
New Correlations Between Monotonic and Cyclic Properties of Metallic Materials
,”
J. Mater. Eng. Perform.
,
26
(
4
), pp.
1569
–
1580
.10.1007/s11665-017-2595-9
15.
Nishikawa
,
H.
, and
Furuya
,
Y.
,
2019
, “
Cyclic Yield Characterization for Low-Carbon Steel With HAZ Microstructures
,”
Mater. Trans.
,
60
(
2
), pp.
207
–
212
.10.2320/matertrans.ME201717
16.
ASTM
,
2013
, Standard Test Method for Measurement of Fatigue Crack Growth Rates,
ASTM International
,
West Conshohocken, PA
, Standard No.
ASTM E647-13E1
. https://www.astm.org/DATABASE.CART/HISTORICAL/E647-13E1.htm
17.
ASTM
,
1997
, Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials,
ASTM International
,
West Conshohocken, PA
, Standard No.
ASTM E399-90
.https://www.astm.org/DATABASE.CART/HISTORICAL/E647-13E1.htm
18.
NASGRO
,
2010
, “
Fracture Mechanics and Fatigue Crack Growth Analysis Software (Version 6.0), Reference Manual
,” NASA Johnson Space Center and Southwest Research Institute, San Antonio, TX.
19.
Madia
,
M.
,
Zerbst
,
U.
,
Beier
,
H. T.
, and
Schork
,
B.
,
2018
, “
The IBESS Model–Elements, Realisation and Validation
,”
Eng. Fract. Mech.
,
198
, pp.
171
–
208
.10.1016/j.engfracmech.2017.08.033
20.
Newman
,
J. J.
,
1981
, “
A Crack-Closure Model for Predicting Fatigue-Crack Growth Under Aircraft Spectrum Loading
,” NASA Technical Memorandum, NASA Langley Research Center, Hampton, VA, Report No.
NASA-TM-81941
.https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/19810009887.pdf
21.
McClung
,
R. C.
,
Chell
,
G. G.
,
Lee
,
Y.-D.
,
Russell
,
D. A.
, and
Orient
,
G. E.
,
1999
, “
Development of a Practical Methodology for Elastic-Plastic and Fully Plastic Fatigue Crack Growth
,” Southwest Research Inst., San Antonio, TX, Report No.
NASA/CR-1999-209428
. https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/19990063917.pdf
Copyright © 2020 by ASME
You do not currently have access to this content.