There is a need to measure contact pressures at the femoral component and tibia plate of a knee arthroplasty implant to determine the wear and tear of the polyethylene (PE) insert of the implant. Today, most pressure monitoring systems for knee arthroplasty implants are either limited to in vitro or intraoperative use, or cannot measure contact pressures at the polyethylene surface. Here, we are developing a wireless passive sensor system for measuring the contact pressure at the knee arthroplasty in vivo. The sensor system is made of a pressure-sensitive magnetic layer embedded under the top surface of a PE insert used for mapping the contact pressures with the femoral components. The pressure-sensing layer consists of a grid of pressure and stress sensitive magnetoelastic thin strips that alter their magnetic properties with applied force. Measurements are taken at pressure points located at the crossings of the grid. The magnetization of each sensing strip is remotely measured by using an AC magnetic field to excite the material to generate higher-frequency fields, which are then detected through external detection coils. The responses of these sensing strips are fed into an algorithm to determine the pressure loadings at all pressure points, which allows for real-time, in vivo determination of pressure profiles on the PE insert. By using an array of magnetoelastic sensing strips, we have demonstrated the remote detection of pressure across a surface. The 2nd order harmonic amplitude of a 30 mm1.5mm magnetoelastic strip decreased linearly with increasing pressure. For this sensing strip, the rate of decrease was about 0.1 (normalized to unstressed signal level) per 200 kPa. An algorithm was also developed to determine the pressures at all pressure points from the responses of the sensing strips. Experimental results have shown that the algorithm can accurately map the pressure profile of a 33 sensing strip array. Further works include developing a fabrication process for safely embedding the sensing strips into a PE insert, and modifying the algorithm for a larger sensing strip array.
Skip Nav Destination
Article navigation
Design Of Medical Devices Conference Abstracts
Real-Time, In Vivo Measurement of Contact Pressures at a Knee Arthroplasty
B. Pereles,
B. Pereles
Michigan Technological University
, Houghton, USA
Search for other works by this author on:
E. Tan,
E. Tan
Michigan Technological University
, Houghton, USA
Search for other works by this author on:
K. Ong
K. Ong
Michigan Technological University
, Houghton, USA
Search for other works by this author on:
B. Pereles
Michigan Technological University
, Houghton, USA
E. Tan
Michigan Technological University
, Houghton, USA
K. Ong
Michigan Technological University
, Houghton, USAJ. Med. Devices. Jun 2009, 3(2): 027505 (1 pages)
Published Online: June 30, 2009
Article history
Published:
June 30, 2009
Citation
Pereles, B., Tan, E., and Ong, K. (June 30, 2009). "Real-Time, In Vivo Measurement of Contact Pressures at a Knee Arthroplasty." ASME. J. Med. Devices. June 2009; 3(2): 027505. https://doi.org/10.1115/1.3134840
Download citation file:
589
Views
Get Email Alerts
Cited By
Related Articles
Bioactive Magnetoelastic Materials as Coatings for Implantable Biomaterials
J. Med. Devices (June,2009)
PMMA Implants Increase Femoral Strength
J. Med. Devices (June,2008)
Human Joint Simulation Using LifeMOD Co-Simulation
J. Med. Devices (June,2008)
Novel re-entrant porous composite structure: a potential for orthopaedic applications
J. Med. Devices (June,2008)
Related Proceedings Papers
Related Chapters
Experimental Investigation of Ventilated Supercavitation Under Unsteady Conditions
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Friction and Wear of Polymers and Composites
Tribology of Mechanical Systems: A Guide to Present and Future Technologies
Hydrogen Compatibility of Polymers for Infrastructure Applications: Friction and Wear
International Hydrogen Conference (IHC 2016): Materials Performance in Hydrogen Environments