Laser welding of advanced high strength steels for fabrication of tailor welded blanks is of increasing interest for continued improvements in vehicle performance and safety without an increase in weight. Experimental results have shown that formability of welded dual-phase (DP) steels is significantly reduced by the formation of a softened region in the heat-affected zone (HAZ). In this study, a finite element simulation of welded DP980 samples undergoing transverse uniaxial tensile testing was used to evaluate the effects of soft zone width and strength on formability characteristics. Both the strength and the ductility of laser welded blanks decreased compared with those of unwelded blanks due to the formation of a softened outer-HAZ, where strain localization and final fracture occurred during tensile testing. The magnitude of softening and the width of the HAZ depend on the laser specific energy. It was observed from tensile test experiments and numerical simulations that both a decrease in strength and an increase in width of the softened HAZ were responsible for a decrease in the overall strength and ductility of the welded blanks.
Skip Nav Destination
e-mail: s2panda@engmail.uwaterloo.ca
Article navigation
October 2008
Research Papers
Numerical Simulations and Experimental Results of Tensile Test Behavior of Laser Butt Welded DP980 Steels
S. K. Panda,
S. K. Panda
Centre for Advanced Materials Joining,
e-mail: s2panda@engmail.uwaterloo.ca
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
Search for other works by this author on:
N. Sreenivasan,
N. Sreenivasan
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
Search for other works by this author on:
M. L. Kuntz,
M. L. Kuntz
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
Search for other works by this author on:
Y. Zhou
Y. Zhou
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
Search for other works by this author on:
S. K. Panda
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canadae-mail: s2panda@engmail.uwaterloo.ca
N. Sreenivasan
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
M. L. Kuntz
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, Canada
Y. Zhou
Centre for Advanced Materials Joining,
University of Waterloo
, Waterloo, ON, N2L 3G1, CanadaJ. Eng. Mater. Technol. Oct 2008, 130(4): 041003 (9 pages)
Published Online: August 26, 2008
Article history
Received:
December 31, 2007
Revised:
July 2, 2008
Published:
August 26, 2008
Citation
Panda, S. K., Sreenivasan, N., Kuntz, M. L., and Zhou, Y. (August 26, 2008). "Numerical Simulations and Experimental Results of Tensile Test Behavior of Laser Butt Welded DP980 Steels." ASME. J. Eng. Mater. Technol. October 2008; 130(4): 041003. https://doi.org/10.1115/1.2969256
Download citation file:
Get Email Alerts
Evaluation of Machine Learning Models for Predicting the Hot Deformation Flow Stress of Sintered Al–Zn–Mg Alloy
J. Eng. Mater. Technol (April 2025)
Blast Mitigation Using Monolithic Closed-Cell Aluminum Foam
J. Eng. Mater. Technol (April 2025)
Irradiation Damage Evolution Dependence on Misorientation Angle for Σ 5 Grain Boundary of Nb: An Atomistic Simulation-Based Study
J. Eng. Mater. Technol (July 2025)
Related Articles
A Comparative Study of Formability of Diode Laser Welds in DP980 and HSLA Steels
J. Eng. Mater. Technol (July,2007)
Effect of Laser Welding on Formability of DP980 steel
J. Eng. Mater. Technol (October,2008)
Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios
J. Eng. Mater. Technol (April,2005)
Interfacial Structure and Micro and Nano-Mechanical Behavior of Laser-Welded 6061 Aluminum Alloy Blank
J. Eng. Mater. Technol (January,2004)
Related Proceedings Papers
Related Chapters
Defining Joint Quality Using Weld Attributes
Ultrasonic Welding of Lithium-Ion Batteries
Materials and Their Weldability
A Quick Guide to Welding and Weld Inspection
A 3D Cohesive Modelling Approach for Hydrogen Embrittlement in Welded Joints of X70 Pipeline Steel
International Hydrogen Conference (IHC 2012): Hydrogen-Materials Interactions