Robotized filament winding technology allows one to manufacture workpieces of high performances as a result of a robot placing fibers impregnated by resin (known as roving) along the directions of stresses the workpiece is subjected to in exercise; thus, robotized filament winding favors rigidity and strength of a workpiece along some preferential directions. A proper value of the winding tension has to be chosen and kept constant along the whole winding in order to limit the defects inside the composite workpieces. To keep the tension value on roving near to the nominal value, one must plan the value of the geometric parameters characterizing the winding trajectory. The same geometric parameters influence the value of the actual safety distance that may involve collisions among the deposition system and the components of the robotized cell. This work shows how to avoid the occurrence of collisions by planning the value of the actual safety distance through the definition of geometric parameters that characterize the winding trajectory. Moreover, the collision occurrence should be considered together with the control of the winding tension on the roving in the robotized filament winding planning stage. The present work shows how to solve both the problems previously defined (i.e., to keep the winding tension on roving near to the nominal value and to avoid collision occurrence), by the solution of a constrained optimization system.
Skip Nav Destination
e-mail: sorrentino@unicas.it
Article navigation
July 2006
Research Papers
Actual Safety Distance and Winding Tension to Manufacture Full Section Parts by Robotized Filament Winding
W. Polini,
W. Polini
Dipartimento di Ingegneria Industriale,
Università degli Studi di Cassino
, Via G. di Biasio, 43, 03043 Cassino, Italy
Search for other works by this author on:
L. Sorrentino
L. Sorrentino
Dipartimento di Ingegneria Industriale,
e-mail: sorrentino@unicas.it
Università degli Studi di Cassino
, Via G. di Biasio, 43, 03043 Cassino, Italy
Search for other works by this author on:
W. Polini
Dipartimento di Ingegneria Industriale,
Università degli Studi di Cassino
, Via G. di Biasio, 43, 03043 Cassino, Italy
L. Sorrentino
Dipartimento di Ingegneria Industriale,
Università degli Studi di Cassino
, Via G. di Biasio, 43, 03043 Cassino, Italye-mail: sorrentino@unicas.it
J. Eng. Mater. Technol. Jul 2006, 128(3): 393-400 (8 pages)
Published Online: December 23, 2005
Article history
Received:
May 17, 2005
Revised:
December 23, 2005
Citation
Polini, W., and Sorrentino, L. (December 23, 2005). "Actual Safety Distance and Winding Tension to Manufacture Full Section Parts by Robotized Filament Winding." ASME. J. Eng. Mater. Technol. July 2006; 128(3): 393–400. https://doi.org/10.1115/1.2203099
Download citation file:
Get Email Alerts
Cited By
Evaluation of Machine Learning Models for Predicting the Hot Deformation Flow Stress of Sintered Al–Zn–Mg Alloy
J. Eng. Mater. Technol (April 2025)
Blast Mitigation Using Monolithic Closed-Cell Aluminum Foam
J. Eng. Mater. Technol (April 2025)
Irradiation Damage Evolution Dependence on Misorientation Angle for Σ 5 Grain Boundary of Nb: An Atomistic Simulation-Based Study
J. Eng. Mater. Technol (July 2025)
Related Articles
Stress Field in Finite Width Axisymmetric Wound Rolls
J. Appl. Mech (March,2002)
A Hybrid Approach for Quantifying the Winding Process and Material Effects on Sheet Coil Deformation
J. Eng. Mater. Technol (July,2004)
Effect of Semi-Geodesic Winding on the Vibration Characteristics of Filament Wound Shells of Revolution
J. Appl. Mech (November,2011)
Transient Thermal Modeling of In-Situ Curing During Tape Winding of Composite Cylinders
J. Heat Transfer (February,2003)
Related Proceedings Papers
Related Chapters
Completing the Picture
Air Engines: The History, Science, and Reality of the Perfect Engine
A Novel Anti-Slip Pad for Improving Steering when Exiting a Ski Lift on a Snowboard
Skiing Trauma and Safety: 17th Volume
The Dynamic Role Played by the Ice Hockey Stick
Safety in Ice Hockey