Skip Nav Destination
Issues
August 2002
ISSN 1087-1357
EISSN 1528-8935
In this Issue
Technical Papers
Characterization of Sheet Buckling Subjected to Controlled Boundary Constraints
J. Manuf. Sci. Eng. August 2002, 124(3): 493–501.
doi: https://doi.org/10.1115/1.1475990
Topics:
Buckling
,
Boundary-value problems
,
Geometry
,
Stress
Control of Transient Thermal Response During Sequential Open-Die Forging: A Trajectory Optimization Approach
W. G. Frazier, Senior Engineer,, T. Seshacharyulu, Visiting Scientist, S. C. Medeiros, Materials Engineer, Y. V. R. K. Prasad, Professor
J. Manuf. Sci. Eng. August 2002, 124(3): 502–508.
doi: https://doi.org/10.1115/1.1467076
Topics:
Design
,
Forging
,
Furnaces
,
Optimization
,
Temperature
,
Temperature distribution
,
Trajectories (Physics)
,
Transients (Dynamics)
,
Heating
,
Deformation
Prediction and Compensation of Dynamic Errors for Coordinate Measuring Machines
J. Manuf. Sci. Eng. August 2002, 124(3): 509–514.
doi: https://doi.org/10.1115/1.1465435
A Reflective Fiber Optic Sensor for Surface Roughness In-Process Measurement
J. Manuf. Sci. Eng. August 2002, 124(3): 515–522.
doi: https://doi.org/10.1115/1.1475991
Topics:
Fiber optic sensors
,
Reflection
,
Sensors
,
Simulation
,
Surface roughness
,
Fibers
,
Probes
,
Simulation results
,
Design
,
Engineering prototypes
An Embedded Friction Sensor Based on a Strain-Gauged Diaphragm
J. Manuf. Sci. Eng. August 2002, 124(3): 523–527.
doi: https://doi.org/10.1115/1.1461839
Topics:
Diaphragms (Mechanical devices)
,
Diaphragms (Structural)
,
Friction
,
Sensors
,
Shear (Mechanics)
,
Strain gages
,
Stress
The Mechanisms of Chip Formation in Machining Hardened Steels
J. Manuf. Sci. Eng. August 2002, 124(3): 528–535.
doi: https://doi.org/10.1115/1.1455643
Topics:
Cutting
,
Deformation
,
Machining
,
Shear (Mechanics)
,
Steel
,
Ductile fracture
,
Martensitic steel
Application of an Internally Consistent Material Model to Determine the Effect of Tool Edge Geometry in Orthogonal Machining
J. Manuf. Sci. Eng. August 2002, 124(3): 536–543.
doi: https://doi.org/10.1115/1.1448334
Topics:
Cutting
,
Geometry
,
Machining
,
Shear (Mechanics)
,
Shear stress
,
Stress
,
Separation (Technology)
Modeling Cutting Temperatures for Turning Inserts With Various Tool Geometries and Materials
J. Manuf. Sci. Eng. August 2002, 124(3): 544–552.
doi: https://doi.org/10.1115/1.1461838
Topics:
Cutting
,
Finite element analysis
,
Temperature
,
Thermocouples
,
Modeling
,
Heat
Machining Simulation for Ceramics Based on Continuum Damage Mechanics
J. Manuf. Sci. Eng. August 2002, 124(3): 553–561.
doi: https://doi.org/10.1115/1.1463034
Topics:
Ceramics
,
Damage
,
Machining
,
Simulation
,
Stress
,
Damage mechanics
Dynamic Behavior of a Thin-Walled Cylindrical Workpiece During the Turning Process, Part 1: Cutting Process Simulation
J. Manuf. Sci. Eng. August 2002, 124(3): 562–568.
doi: https://doi.org/10.1115/1.1431260
Dynamic Behavior of a Thin-Walled Cylindrical Workpiece During the Turning-Cutting Process, Part 2: Experimental Approach and Validation
J. Manuf. Sci. Eng. August 2002, 124(3): 569–580.
doi: https://doi.org/10.1115/1.1432667
Topics:
Aluminum alloys
,
Cutting
,
Vibration
,
Turning
,
Chatter
A Stability Solution for the Axial Contour-Turning Process
J. Manuf. Sci. Eng. August 2002, 124(3): 581–587.
doi: https://doi.org/10.1115/1.1480415
The Effect of Workpiece Hardness and Cutting Speed on the Machinability of AISI H13 Hot Work Die Steel When Using PCBN Tooling
J. Manuf. Sci. Eng. August 2002, 124(3): 588–594.
doi: https://doi.org/10.1115/1.1452749
Topics:
Cutting
,
Shear (Mechanics)
,
Machining
,
Steel
,
Temperature
,
Stress
,
Heat
Laser Repetitive Pulse Heating of Steel Surface: A Material Response to Thermal Loading
J. Manuf. Sci. Eng. August 2002, 124(3): 595–604.
doi: https://doi.org/10.1115/1.1463033
Topics:
Flow (Dynamics)
,
Heating
,
Lasers
,
Steel
,
Stress
,
Temperature
,
Thermal stresses
,
Turbulence
,
Heat conduction
,
Laser beams
Modeling Chip-Evacuation Forces and Prediction of Chip-Clogging in Drilling
Jeffrey C. Mellinger, Graduate Research Assistant, O. Burak Ozdoganlar, Post Doctoral Research Associate, Richard E. DeVor, Professor, Shiv G. Kapoor, Professor
J. Manuf. Sci. Eng. August 2002, 124(3): 605–614.
doi: https://doi.org/10.1115/1.1473146
Topics:
Calibration
,
Cutting
,
Drilling
,
Drills (Tools)
,
Evacuations
,
Torque
,
Friction
Process Parameters and Residual Stresses in Cylindrical Grinding
J. Manuf. Sci. Eng. August 2002, 124(3): 615–623.
doi: https://doi.org/10.1115/1.1428328
Generic Simulation Approach for Multi-Axis Machining, Part 1: Modeling Methodology
J. Manuf. Sci. Eng. August 2002, 124(3): 624–633.
doi: https://doi.org/10.1115/1.1468863
Topics:
Cutting
,
Geometry
,
Machining
,
Modeling
,
Simulation
,
Topology
,
Deflection
Generic Simulation Approach for Multi-Axis Machining, Part 2: Model Calibration and Feed Rate Scheduling
J. Manuf. Sci. Eng. August 2002, 124(3): 634–642.
doi: https://doi.org/10.1115/1.1468864
Topics:
Calibration
,
Cutting
,
Machining
,
Deflection
,
Airfoils
Prediction of Thread Quality by Detection and Estimation of Tapping Faults
Oleg A. Mezentsev, Graduate Research Assistant, Richard E. DeVor, Professor, Shiv G. Kapoor, Professor
J. Manuf. Sci. Eng. August 2002, 124(3): 643–650.
doi: https://doi.org/10.1115/1.1475319
Topics:
Thread
Hidden Markov Model-based Tool Wear Monitoring in Turning
J. Manuf. Sci. Eng. August 2002, 124(3): 651–658.
doi: https://doi.org/10.1115/1.1475320
Phase Transformation and Its Effect on Flank Wear in Machining Steels
J. Manuf. Sci. Eng. August 2002, 124(3): 659–666.
doi: https://doi.org/10.1115/1.1473145
Topics:
Cutting
,
Machining
,
Phase transitions
,
Steel
,
Wear
,
X-ray diffraction
,
Temperature
Kinematic Characterization of Chip Lateral-Curl—The Third Pattern of Chip Curl in Machining
J. Manuf. Sci. Eng. August 2002, 124(3): 667–675.
doi: https://doi.org/10.1115/1.1468225
Topics:
Cutting
,
Flow (Dynamics)
,
Kinematics
,
Machining
Optimal Placement of Fixture Clamps: Maintaining Form Closure and Independent Regions of Form Closure
J. Manuf. Sci. Eng. August 2002, 124(3): 676–685.
doi: https://doi.org/10.1115/1.1471527
Topics:
Computation
,
Linear programming
,
Screws
,
Stress
,
Uncertainty
,
Algebra
,
Clamps (Tools)
,
Errors
,
Optimization
Optimal Placement of Fixture Clamps: Minimizing the Maximum Clamping Forces
J. Manuf. Sci. Eng. August 2002, 124(3): 686–694.
doi: https://doi.org/10.1115/1.1469520
Topics:
Friction
,
Stress
,
Clamps (Tools)
,
Optimization
Sensing and Control of Double-Sided Arc Welding Process
J. Manuf. Sci. Eng. August 2002, 124(3): 695–701.
doi: https://doi.org/10.1115/1.1467603
Topics:
Arc welding
,
Control systems
,
Density
,
Welding
,
Electrodes
,
Flow (Dynamics)
,
Sensors
,
Plasma jets
,
Electric arcs
,
Stainless steel
Development of the Cylindrical Wire Electrical Discharge Machining Process, Part 1: Concept, Design, and Material Removal Rate
J. Manuf. Sci. Eng. August 2002, 124(3): 702–707.
doi: https://doi.org/10.1115/1.1475321
Topics:
Electrical discharge machining
,
Wire
,
Design
,
Machinery
Development of the Cylindrical Wire Electrical Discharge Machining Process, Part 2: Surface Integrity and Roundness
J. Manuf. Sci. Eng. August 2002, 124(3): 708–714.
doi: https://doi.org/10.1115/1.1475989
Topics:
Electrical discharge machining
,
Finishes
,
Surface roughness
,
Wire
,
Brass (Metal)
,
Heat
Control of Thin Film Growth in Chemical Vapor Deposition Manufacturing Systems: A Feasibility Study
J. Manuf. Sci. Eng. August 2002, 124(3): 715–724.
doi: https://doi.org/10.1115/1.1465434
Topics:
Chemical vapor deposition
,
Design
,
Optimization
,
Temperature
,
Thin films
,
Computer simulation
Kinetostatic Analysis and Design Optimization of the Tricept Machine Tool Family
J. Manuf. Sci. Eng. August 2002, 124(3): 725–733.
doi: https://doi.org/10.1115/1.1471529
Topics:
Design
,
Genetic algorithms
,
Machine tools
,
Optimization
,
Stiffness
,
Actuators
,
Kinematics
,
Machinery
Modeling the HSK Toolholder-Spindle Interface
J. Manuf. Sci. Eng. August 2002, 124(3): 734–744.
doi: https://doi.org/10.1115/1.1480023
Topics:
Stress
A Methodology for Predicting the Variance of Fatigue Life Incorporating the Effects of Manufacturing Processes
J. Manuf. Sci. Eng. August 2002, 124(3): 745–753.
doi: https://doi.org/10.1115/1.1475318
Topics:
Fatigue life
,
Stress
,
Manufacturing
Development of a Computer-Aided Manufacturing System for Profiled Edge Lamination Tooling
J. Manuf. Sci. Eng. August 2002, 124(3): 754–761.
doi: https://doi.org/10.1115/1.1467077
Optimization of Design Tolerances Through Response Surface Approximations
J. Manuf. Sci. Eng. August 2002, 124(3): 762–767.
doi: https://doi.org/10.1115/1.1381400
Topics:
Approximation
,
Design
,
Optimization
,
Response surface methodology
,
Manufacturing
,
Simulation
,
Dimensions
In Memoriam
J. Manuf. Sci. Eng. August 2002, 124(3): 768–769.
doi: https://doi.org/10.1115/1.1492293
Topics:
Cutting
,
Engineering teachers
,
Machining
,
Metal cutting
,
Metals
Email alerts
RSS Feeds
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
A Generalized Machining Process Damping Model for Orthogonal Cutting
J. Manuf. Sci. Eng