The focus of this work is to study the effects of anisotropic thermal conductivity and thermal contact conductance on the overall temperature distribution inside a fuel cell. The gas-diffusion layers and membrane are expected to possess an anisotropic thermal conductivity, whereas a contact resistance is present between the current collectors and gas-diffusion layers. A two-dimensional single phase model is used to capture transport phenomena inside the cell. From the use of this model, it is predicted that the maximum temperatures inside the cell can be appreciably higher than the operating temperature of the cell. A high value of the in-plane thermal conductivity for the gas-diffusion layers was seen to be essential for achieving smaller temperature gradients. However, the maximum improvement in the heat transfer characteristics of the fuel cell brought about by increasing the in-plane thermal conductivity is limited by the presence of a finite thermal contact conductance at the diffusion layer/current collector interface. This was determined to be even more important for thin gas-diffusion layers. Anisotropic thermal conductivity of the membrane, however, did not have a significant impact on the temperature distribution. The thermal contact conductance at the diffusion layer/current collector interface strongly affected the temperature distribution inside the cell.
Skip Nav Destination
e-mail: cjb282@psu.edu
e-mail: Thynell@psu.edu
Article navigation
September 2007
This article was originally published in
Journal of Heat Transfer
Technical Papers
Anisotropic Heat Conduction Effects in Proton-Exchange Membrane Fuel Cells
Chaitanya J. Bapat,
Chaitanya J. Bapat
Graduate Research Assistant
Department of Mechanical and Nuclear Engineering,
e-mail: cjb282@psu.edu
The Pennsylvania State University
, University Park, PA 16802
Search for other works by this author on:
Stefan T. Thynell
Stefan T. Thynell
Fellow ASME
Department of Mechanical and Nuclear Engineering,
e-mail: Thynell@psu.edu
The Pennsylvania State University
, University Park, PA 16802
Search for other works by this author on:
Chaitanya J. Bapat
Graduate Research Assistant
Department of Mechanical and Nuclear Engineering,
The Pennsylvania State University
, University Park, PA 16802e-mail: cjb282@psu.edu
Stefan T. Thynell
Fellow ASME
Department of Mechanical and Nuclear Engineering,
The Pennsylvania State University
, University Park, PA 16802e-mail: Thynell@psu.edu
J. Heat Transfer. Sep 2007, 129(9): 1109-1118 (10 pages)
Published Online: July 26, 2006
Article history
Received:
November 14, 2005
Revised:
July 26, 2006
Citation
Bapat, C. J., and Thynell, S. T. (July 26, 2006). "Anisotropic Heat Conduction Effects in Proton-Exchange Membrane Fuel Cells." ASME. J. Heat Transfer. September 2007; 129(9): 1109–1118. https://doi.org/10.1115/1.2712478
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Effect of Nonuniform Stack Compression on Proton Exchange Membrane Fuel Cell Temperature Distributions
J. Heat Transfer (December,2008)
The Effect of Compressive Load on Proton Exchange Membrane Fuel Cell Stack Performance and Behavior
J. Heat Transfer (August,2007)
Transport Phenomena Analysis in Proton Exchange Membrane Fuel Cells
J. Heat Transfer (December,2005)
Multi-Resolution PEM Fuel Cell Model Validation and Accuracy Analysis
J. Fuel Cell Sci. Technol (February,2006)
Related Proceedings Papers
Related Chapters
Experimental Investigation of an Improved Thermal Response Test Equipment for Ground Source Heat Pump Systems
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Orthotropic Media
Thermal Spreading and Contact Resistance: Fundamentals and Applications
Further Applications of Spreading Resistance
Thermal Spreading and Contact Resistance: Fundamentals and Applications