There has been a growing interest in porous systems with a smaller length-scale modeling requirement on the order of each particle, where the existing tools tend to be inadequate. To address this, a Discrete Conduction Model was recently proposed to allow for the transient temperature calculation of 3D random packed-sphere systems for various microstructures. Since many of the motivating applications involve contacting spheres and since there has been a limited number of contact-resistance studies on spheres undergoing elastic deformation, the objective of this study is to obtain measurements of the contact resistances between metallic spheres in elastic contact, as well as to quantify their influence on the effective thermal conductivity. To accomplish this, an experiment was constructed utilizing air and interfacial resistance to replace the functions of the guard heater and vacuum chamber, and in so doing, enabled transient observations. The overall uncertainty was estimated to be ±6%, and the results were benchmarked against available data. A correlation was obtained relating the contact resistance with the contact radius, and results showed the contact resistance to have minimal transient behavior. The results also showed that the neglect of contact resistance could incur an error in the effective thermal conductivity calculation as large as 800%, and a guideline was presented under which the effect of the contact resistance may be ignored. A correlation accounting for the effect of contact resistance on the effective thermal conductivity was also presented.

Issue Section:
Research Paper
Keywords:
heat conduction, thermal conductivity, porous materials, elastic deformation, mechanical contact
Topics:
Contact resistance, Pistons, Thermal conductivity, Temperature, Deformation, Heat conduction
1.
Siu
,
W. W. M.
, and
Lee
,
S. H.-K.
,
2004
, “
Transient Temperature Computation of Spheres in Three-Dimensional Random Packings
,”
Int. J. Heat Mass Transfer
,
47
(
5
), pp.
887
–
898
.
2.
Kaviany, M., 1995, Principle of Heat Transfer in Porous Media, Springer, New York.
3.
Wu
,
A. K. C.
, and
Lee
,
S. H.-K.
,
2000
, “
Sphere Packing Algrithm for Heat Transfer Studies
,”
Numer. Heat Transfer, Part A
,
37
(
6
), pp.
631
–
652
.
4.
Snaith
,
B.
,
Probert
,
S. D.
, and
O’Callaghan
,
P. W.
,
1986
, “
Thermal Resistances of Pressed Contacts
,”
Appl. Energy
,
22
, pp.
31
–
84
.
5.
Peterson
,
G. P.
, and
Fletcher
,
L. S.
,
1988
, “
Thermal Contact Conductance of Packed Beds in Contact With a Flat Surface
,”
ASME J. Heat Transfer
,
110
, pp.
38
–
41
.
6.
Kamiuto
,
K.
, and
Saitoh
,
S.
,
1995
, “
Simultaneous Heat and Mass Transfer in Packed Bed Catalytic Reactors
,”
J. Thermophys. Heat Transfer
,
9
(
3
), pp.
524
–
530
.
7.
Fisher
,
N. J.
, and
Yovanovich
,
M. M.
,
1989
, “
Thermal Constriction Resistance of Sphere/Layer Flat Contacts: Theory and Experiment
,”
ASME J. Heat Transfer
,
111
, pp.
249
–
256
.
8.
Sridhar, M. R., and Yovanovich, M. M., 1993, “Elastoplastic Constriction Resistance of Sphere/Flat Contacts: Theory and Experiment,” ASME HTD-Vol. 263, Enhanced Cooling Techniques for Electronics Applications, ASME, New York, pp. 123–134.
9.
Lambert
,
M. A.
, and
Fletcher
,
L. S.
,
1997
, “
Thermal Contact Conductance of Spherical Rough Metals
,”
ASME J. Heat Transfer
,
119
, pp.
684
–
690
.
10.
Nishino
,
K.
,
Yamashita
,
S.
, and
Torii
,
K.
,
1995
, “
Thermal Contact Conductance Under Low Applied Load in a Vacuum Environment
,”
Exp. Therm. Fluid Sci.
,
10
, pp.
258
–
271
.
11.
Madhusudana, C. V., 1995, Thermal Contact Conductance, Springer, New York.
12.
Timoshenko, S., and Goodier, J. N., 1951, Theory of Elasticity, McGraw-Hill, New York.
13.
Maccni, R. R., 1988, “Characteristics Crucial to the Application of Engineering Plastics,” Engineering Materials Handbook—Vol. 2 Engineering Plastics, ASM, Metals Park, OH.
14.
Beckwith, T. G., Buck, N. L., and Maragoni, R. D., 1982, Mechanical Measurement, Addison Wesley, Reading, MA.
15.
Lambert, M. A., Marotta, E. E., and Fletcher, L. S., 1993, “The Thermal Contact Conductance of Hard and Soft Coat Anodized Aluminum,” ASME HTD-Vol. 263, Enhanced Cooling Technique for Electronics Applications, ASME, New York, pp. 135–141.
Copyright © 2004
 by ASME
You do not currently have access to this content.