This paper addresses the fundamental problem of how to facilitate the flow of heat across a conducting slab heated from one side. Available for distribution through the system is a small amount of high-conductivity material. The constructal method consists of optimizing geometrically the distribution of the high-conductivity material through the material of lower conductivity. Two-dimensional distributions (plate inserts) and three-dimensional distributions (pin inserts) are optimized based on the numerical simulation of heat conduction in a large number of possible configurations. Results are presented for the external and internal features of the optimized architectures: spacings between inserts, penetration distances, tapered inserts and constant-thickness inserts. The use of optimized pin inserts leads consistently to lower global thermal resistances than the use of plate inserts. The side of the slab that is connected to the high-conductivity intrusions is in effect a “rough” surface. This paper shows that the architecture of a rough surface can be optimized for minimum global contact resistance. Roughness can be designed.

Issue Section:
Technical Notes
Keywords:
heat conduction, numerical analysis, Contact Resistance, Heat Transfer, Interface, Packaging, Roughness, Constructal Design
Topics:
Design, Electrical conductivity, Heat conduction, Surface roughness, Thermal conductivity, Slabs, Contact resistance, Heat
1.
Bejan, A., 2000, Shape and Structure, from Engineering to Nature, Cambridge University Press, Cambridge, UK.
2.
Bejan, A., 1997, Advanced Engineering Thermodynamics, 2nd ed. chap. 13, John Wiley and Sons, New York.
3.
Bejan
,
A.
,
1997
, “
Constructal-Theory Network of Conducting Paths for Cooling a Heat Generating Volume
,”
Int. J. Heat Mass Transf.
,
40
, pp.
799
–
816
.
4.
Bar-Cohen
,
A.
, and
Rohsenow
,
W. M.
,
1984
, “
Thermally Optimum Spacing of Vertical, Natural Convection Cooled, Parallel Plates
,”
ASME J. Heat Transfer
,
106
, pp.
116
–
123
.
5.
Peterson
,
G. P.
, and
Ortega
,
A.
,
1990
, “
Thermal Control of Electronic Equipment and Devices
,”
Adv. Heat Transfer
,
20
, pp.
181
–
314
.
6.
Knight
,
R. W.
,
Goodling
,
J. S.
, and
Hall
,
D. J.
,
1991
, “
Optimal Thermal Design of Forced Convection Heat Sinks—Analytical
,”
ASME J. Electron. Packag.
,
113
, pp.
313
–
321
.
7.
Anand
,
N. K.
,
Kim
,
S. H.
, and
Fletcher
,
L. S.
,
1992
, “
The Effect of Plate Spacing on Free Convection Between Heated Parallel Plates
,”
ASME J. Heat Transfer
,
114
, pp.
515
–
518
.
8.
Kakac, S., Yu¨ncu¨, H., and Hijikata, K., eds., 1994, Cooling of Electronic Systems, Kluwer, Dordrecht, The Netherlands.
9.
Ledezma
,
G. A.
,
Bejan
,
A.
, and
Errera
,
M. R.
,
1997
, “
Constructal Tree Networks for Heat Transfer
,”
J. Appl. Phys.
,
82
, pp.
89
–
100
.
10.
Pozrikidis
,
C.
,
1993
, “
Unsteady Viscous Flow Over Irregular Boundaries
,”
J. Fluid Mech.
,
255
, pp.
11
–
34
.
11.
Brady
,
M.
, and
Pozrikidis
,
C.
,
1993
, “
Diffusive Transport Across Irregular and Fractal Walls
,”
Proc. R. Soc. London, Ser. A
,
442
, pp.
571
–
583
.
12.
Fyrillas
,
M. M.
, and
Pozrikidis
,
C.
,
2001
, “
Conductive Heat Transport Across Rough Surfaces and Interfaces between Two Conforming Media
,”
Int. J. Heat Mass Transf.
,
44
,
1789
–
1801
.
13.
FIDAP, Theory Manual, 1993, v. 7, Fluid Dynamics International, Evanston, IL.
14.
Neagu, M., 1999, “Characteristics and Optimization of Composite Systems with Heat Conduction,” Ph.D. thesis, Duke University, Durham, NC.
Copyright © 2001
 by ASME
You do not currently have access to this content.