... efficiency. These effects are related to the modification of the shape and surface roughness of relevant surfaces (compressor and turbine blades and vanes, especially) due to the presence of a thin layer generated by micro/nanosized particle adhesion. Such contaminants are swallowed by the unit...

...Biswajit Roy; Lintu Roy; Sudip Dey This paper presents the effect of eccentricity and surface roughness on the probabilistic performance of two axial groove hydrodynamic journal bearing. In general, it is difficult to quantify experimentally the variabilities involved in dynamic responses...

... direction. Channel size reduction, surface roughness, and circularity tolerance of the as-printed channels were analyzed based on micrographs captured by SEM. Results showed that both channel sizes and hole pitches affected the printing qualities of microchannels. The as-printed channel sizes reduced...

... due to fouling can be analyzed by means of simulation through computational fluid dynamics (CFD) codes. Usually these methods reproduce the deteriorated blades by increasing their surface roughness and thickness. Another approach is the scaling of compressor stage performance maps. A model based...

... that causes increased surface roughness and to some degree changes the shape of the airfoil (if the material build up forms thicker layers of deposits), with subsequent deterioration in performance. Fouling mechanisms are evaluated based on observed data, and a discussion on fouling susceptibility is provided...

... at the calculated Helmholtz frequency of the holes. 16 08 2010 03 09 2010 19 04 2011 19 04 2011 compressors flow friction plates (structures) rotors stators surface roughness test facilities Annular seals using a smooth rotor and a hole-pattern (HP) stator are commonly...

... or for thermal cyclic tests. The former generally provides data for creep of the superalloy and the overall performance, and the later provide data for thermal barrier coating (TBC) spallation as a function of thermally grown oxide thickness, surface roughness, temperature, and thermal mismatch between...

... and on stage performance maps. In this paper, the effect of nonuniform surface roughness on both rotor and stator blades of an axial compressor stage is investigated by using a commercial CFD code. The NASA Stage 37 test case is considered as the baseline geometry and a numerical model already validated...

..., and the effects on thermal contact conductance of important parameters such as the contact pressure, surface roughness, temperature, thermal conductivity, and material strength are investigated. Normalization of the TCC measured in the experimental program was carried out using appropriate surface and material...

.... The role of bend geometry and, in particular, the short and long radii, surface roughness, wall shear stress, and local turbulence, is discussed. Computational fluid dynamics calculations and plant artifact measurements for short- and long-radius bends are presented. The effect of the close proximity...

... rotor of a gas turbine is studied. The design surface roughness is 1.6   μ m , and the contact stresses of compressor segment and turbine segment are σ comp = 64.8   MPa and σ tur = 29.5   MPa , respectively. So the contact stiffness of these shaft segments...

... of temperature fluctuations at the substrate surface. It was found that heat transfer can be reduced by reducing the surface roughness of the coating. The presence of the coating did not promote knock. 21 05 2009 22 05 2009 21 04 2010 21 04 2010 heat transfer internal combustion...

... stage. The model was then used to simulate the occurrence of fouling by imposing different combinations of added thickness and surface roughness levels. The effect of fouling on compressor performances was studied. Reductions in the flow coefficient and in the pressure coefficient were found...

... Verschiedenen Betriebszuständen ,” MS thesis, Institut für Thermische Strömungsmaschinen, Unniversitä Stuttgart. 03 07 2007 09 11 2007 03 04 2008 aerodynamics assembling blades damping engines fasteners friction iterative methods mechanical contact surface roughness turbines...

...Mihai Arghir 03 01 2007 04 01 2007 seals (stoppers) confined flow laminar to turbulent transitions laminar flow turbulence surface roughness The authors are grateful for this experimental validation of the negative direct static stiffness of choked annular seals...

... of wear of piston rings. To quantify the amount of cylinder wear surface roughness parameters of cylinder liners were measured at three positions (top dead center, mid-stroke, and bottom dead center) on thrust and anti-thrust side. A qualitative analysis was also carried out by taking surface profiles...