During the last decades, turbo machine efficiency was considerably increased by using more efficient seals. Brush seals, as a compliant contacting filament seal, have become an attractive alternative to conventional labyrinth seals in the field of aircraft engines as well as in stationary gas and steam turbines. The aim of today's research related to brush seals is to understand the characteristics and their connections, in order to be able to make performance predictions, and to ensure the reliability over a defined operating period. The wear behavior is essentially influenced by frictional contacts at the seal-to-rotor interface during operation. For realistic investigations with representative circumferential velocities, the TU Braunschweig, Germany, operates a specially developed steam test rig which enables endurance investigations under varying operating steam conditions up to 50 bar and 450 °C. Wear measurements and the determination of seal performance characteristics, such as blow down and bristle stiffness, are enabled by an additional test facility, using pressurized cold air up to 8 bar as a working fluid. This work presents the chronological wear development on both rotor and seal sides in a steam test lasting 25 days or 11 days, respectively. Interruptions after stationary and transient intervals were made in order to investigate the degree of wear. Two different seal arrangements, a single tandem seal, and a two-stage single seal arrangement, using different seal elements were considered. Besides a continuous wear development, the results clearly show that the abrasive wear of the brush seal and rotor is mainly caused by transient test operations, particularly by enforced contacts during shaft excursions. Despite the increasing wear to the brushes, all seals have shown a functioning radial-adaptive behavior over the whole test duration with a sustained seal performance. Thereby, it could be shown that the two-stage arrangement displays a load shift during transients, leading to a balanced loading and unloading status for the two single brush seals. From load sharing, and in comparison with the wear data of the tandem seal arrangement, it can be derived that the two-stage seal is less prone to wear. However, the tandem seal arrangement, bearing the higher pressure difference within one configuration, shows a superior sealing performance under constant load, i.e., under stationary conditions.
Skip Nav Destination
Article navigation
Research-Article
Brush Seals Used in Steam Environments—Chronological Wear Development and the Impact of Different Seal Designs
Markus Raben,
Markus Raben
Institute of Jet Propulsion and Turbomachinery,
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: m.raben@ifas.tu-bs.de
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: m.raben@ifas.tu-bs.de
Search for other works by this author on:
Jens Friedrichs,
Jens Friedrichs
Institute of Jet Propulsion and Turbomachinery,
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: j.friedrichs@ifas.tu-bs.de
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: j.friedrichs@ifas.tu-bs.de
Search for other works by this author on:
Thomas Helmis,
Thomas Helmis
Siemens AG,
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: thomas.helmis@siemens.com
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: thomas.helmis@siemens.com
Search for other works by this author on:
Johan Flegler
Johan Flegler
Siemens AG,
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: johan.flegler@siemens.com
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: johan.flegler@siemens.com
Search for other works by this author on:
Markus Raben
Institute of Jet Propulsion and Turbomachinery,
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: m.raben@ifas.tu-bs.de
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: m.raben@ifas.tu-bs.de
Jens Friedrichs
Institute of Jet Propulsion and Turbomachinery,
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: j.friedrichs@ifas.tu-bs.de
TU Braunschweig,
Hermann-Blenk-Str. 37,
Braunschweig 38108, Germany
e-mail: j.friedrichs@ifas.tu-bs.de
Thomas Helmis
Siemens AG,
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: thomas.helmis@siemens.com
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: thomas.helmis@siemens.com
Johan Flegler
Siemens AG,
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: johan.flegler@siemens.com
Power and Gas Division,
Rheinstr. 100,
Mülheim an der Ruhr 45478, Germany
e-mail: johan.flegler@siemens.com
1Corresponding author.
Contributed by the Heat Transfer Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received July 15, 2015; final manuscript received August 30, 2015; published online October 27, 2015. Editor: David Wisler.
J. Eng. Gas Turbines Power. May 2016, 138(5): 051901 (10 pages)
Published Online: October 27, 2015
Article history
Received:
July 15, 2015
Revised:
August 30, 2015
Citation
Raben, M., Friedrichs, J., Helmis, T., and Flegler, J. (October 27, 2015). "Brush Seals Used in Steam Environments—Chronological Wear Development and the Impact of Different Seal Designs." ASME. J. Eng. Gas Turbines Power. May 2016; 138(5): 051901. https://doi.org/10.1115/1.4031531
Download citation file:
Get Email Alerts
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
A Test Facility for the Measurement of Torques at the Shaft to Seal Interface in Brush Seals
J. Eng. Gas Turbines Power (January,1999)
Brush Seal Frictional Heat Generation—Test Rig Design and Validation Under Steam Environment
J. Eng. Gas Turbines Power (March,2017)
Experimental and Theoretical Rotordynamic Coefficients of Smooth and Round-Hole Pattern Water-Fed Annular Seals
J. Eng. Gas Turbines Power (November,2018)
Integral Pumping Devices for Dual Mechanical Seals: Hydraulic Performance Generalization Using Dimensional Analysis
J. Eng. Gas Turbines Power (August,2018)
Related Proceedings Papers
Related Chapters
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Materials
Design and Application of the Worm Gear
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach