This paper investigates a continuous-flow heat engine based on evaporative cooling of hot air at reduced pressure. In this device, hot air is expanded in an expansion turbine, spray-cooled to saturation and re-compressed to ambient pressure in several stages with evaporative cooling between each stage. More work is available in expansion than is required during re-compression, so the device is a heat engine. The device provides a relatively cheap way to boost the power output of open-cycle gas turbines. The principal assumptions for the theoretical model developed herein are that air and water vapor are regarded as ideal gases with constant specific heat capacities. In the absence of losses associated with expansion and compression, the engine produces more power as the inlet temperature and the pressure ratio increase. The effects of irreversibilities are subsequently included in the expansion and compression stages, with realistic values used for the adiabatic efficiencies of turbine and fans. Purification and injection of water are also considered in the overall energy budget. As a typical result for the new engine, if the inlet air is the exhaust of a 56 MW open-cycle gas turbine, the adiabatic efficiencies of turbine and fan are 0.9, the pressure ratio is 6.5 and there is four-stage re-compression, then the power output is 20.5% that of the gas turbine. The power output is sensitive to the adiabatic efficiencies of turbine and fans.
Skip Nav Destination
e-mail: noel.barton@sunoba.com.au
Article navigation
Research Papers
The Expansion-Cycle Evaporation Turbine
N. G. Barton
e-mail: noel.barton@sunoba.com.au
N. G. Barton
Sunoba Pty Ltd
, P.O. Box 1295, Macquarie Centre, NSW 2113, Australia
Search for other works by this author on:
N. G. Barton
Sunoba Pty Ltd
, P.O. Box 1295, Macquarie Centre, NSW 2113, Australia
e-mail: noel.barton@sunoba.com.au
J. Eng. Gas Turbines Power. May 2012, 134(5): 051702 (7 pages)
Published Online: March 5, 2012
Article history
Received:
July 17, 2011
Revised:
July 24, 2011
Online:
March 5, 2012
Published:
March 5, 2012
Citation
Barton, N. G. (March 5, 2012). "The Expansion-Cycle Evaporation Turbine." ASME. J. Eng. Gas Turbines Power. May 2012; 134(5): 051702. https://doi.org/10.1115/1.4004743
Download citation file:
Get Email Alerts
Cited By
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Preface
J. Heat Transfer (April,2005)
Mirror Gas Turbines: A Newly Proposed Method of Exhaust Heat Recovery
J. Eng. Gas Turbines Power (July,2001)
The Regenerative Criteria of an Irreversible Brayton Heat Engine and its General Optimum Performance Characteristics
J. Energy Resour. Technol (September,2006)
Overspray and Interstage Fog Cooling in Gas Turbine Compressor Using Stage-Stacking Scheme—Part I: Development of Theory and Algorithm
J. Thermal Sci. Eng. Appl (September,2010)
Related Proceedings Papers
Related Chapters
The Stirling Engine
Air Engines: The History, Science, and Reality of the Perfect Engine
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Scope of Section I, Organization, and Service Limits
Power Boilers: A Guide to the Section I of the ASME Boiler and Pressure Vessel Code, Second Edition