Open loop, experimental force and power measurements of a radial, redundant-axis, magnetic bearing at temperatures to 1000°F (538°C) and rotor speeds to 15,000 rpm along with theoretical temperature and force models are presented in this paper. The experimentally measured force produced by a single C-core circuit using 22A was 600 lb (2.67 kN) at room temperature and 380 lb (1.69 kN) at 538°C. These values were compared with force predictions based on a one-dimensional magnetic circuit analysis and a thermal analysis of gap growth as a function of temperature. The analysis showed that the reduction of force at high temperature is mostly due to an increase in radial gap due to test conditions, rather than to reduced core permeability. Tests under rotating conditions showed that rotor speed has a negligible effect on the bearing’s static force capacity. One C-core required approximately 340 W of power to generate 190 lb (845 N) of magnetic force at 538°C, however the magnetic air gap was much larger than at room temperature. The data presented are after bearing operation for eleven total hours at 538°C and six thermal cycles.

Issue Section:
Gas Turbines: Structures and Dynamics
Keywords:
magnetic bearings, turbogenerators, power measurement, force measurement, rotors, magnetic circuits, magnetic cores, machine testing, air gaps
Topics:
Magnetic bearings, Rotors, Temperature, High temperature, Bearings, Stress, Stators
1.
Xu, L., Wang, L., and Schweitzer, G., 2000, “Development of Magnetic Bearings for High Temperature Suspension,” Proceedings of the 7th ISMB.
2.
Ohsawa, M., Furuya, E., Marui, E. et al., 1998, “High Temperature Blower for a Molten Carbonate Fuel Cell Supported by Magnetic Bearings,” Proceedings of the 6th ISMB, pp. 32–41.
3.
Mekhiche, M., Nichols, S., Oleksy, J., Young, J., Kiley, J., and Havenhill, D., 2000, “50K RPM, 1100°F Magnetic Bearings for Jet Turbine Engines,” Proceedings of the 7th ISMB.
4.
Mekhiche, M., Nichols, S., Hevenhill, D. et al., 2000, “High-Speed, High-Temperature Magnetic Bearings for Jet Turbine Engine Application,” Proceedings of the International Conference on Electrical Machines (ICEM).
5.
Field, R. J., and Iannello, V., 1998, “A Reliable Magnetic Bearing System for Turbomachinery,” Proceedings of the 6th ISMB, pp. 42–51.
6.
Field, R. J., Sortore, C. K., and Iannello, V., 2000, “A Magnetic Bearing System for More-Electric Engines,” Proceedings of ASME/IGTI Turbo Expo.
7.
Kueser, P. et al., 1967, “Properties of Magnetic Materials for Use in High-Temperature Space Power Systems,” NASA SP-3043.
8.
Kondoleon, A., and Kelleher, W., 2000, “Soft Magnetic Alloys for High Temperature Radial Magnetic Bearings,” Proceedings of the 7th ISMB.
9.
Fingers, R., 1999, “Creep Behavior of Thin Laminations of Iron-Cobalt Alloys for Use in Switched Reluctance Motors and Generators,” AFRL-PR-WP-TR-1999-2053.
10.
Montague, G. T., Jansen, M. J., Provenza, A. P., Jansen, R. H., Ebihara, B., and Palazzolo, A., 2002, “Room Temperature Characterization of a Magnetic Bearing for Turbomachinery,” NASA Tech. Memo-2002-211904.
11.
Minihan, T., Palazzolo, A., Provenza, A., Montague, G. T., and Kascak, A. F., 2002, “Fail Safe, High Temperature Magnetic Bearings,” Proceedings of the ASME/IGTI Turbo Expo.
12.
Jansen, R. H., Ebihara, B. E., Montague, G. T., Provenza, A. J., Jansen, M. J., Palazzolo, A., Tucker, R., Preuss, J., and Hunt, A., 2003, “Design and Fabrication of a High Temperature, Radial Magnetic Bearing for Turbomachinery,” NASA Tech. Memo, 2003-212300.
13.
Knospe, C. R., and Maslen, E. H., 1999, “Introduction to Active Magnetic Bearings,” University of Virginia Short Course.
Copyright © 2005
 by ASME
You do not currently have access to this content.