Abstract

To meet the advanced bearing needs of modern turbomachinery, a hybrid foil-magnetic hybrid bearing system was designed, fabricated, and tested in a test rig designed to simulate the rotor dynamics of a small gas turbine engine (31 kN to 53 kN thrust class). This oil-free bearing system combines the excellent low and zero-speed capabilities of the magnetic bearing with the high-load capacity and high-speed performance of the compliant foil bearing. An experimental program is described which documents the capabilities of the bearing system for sharing load during operation at up to 30,000 rpm and the foil bearing component’s ability to function as a backup in case of magnetic bearing failure. At an operating speed of 22,000 rpm, loads exceeding 5300 N were carried by the system. This load sharing could be manipulated by an especially designed electronic control algorithm. In all tests, rotor excursions were small and stable. During deliberately staged magnetic bearing malfunctions, the foil bearing proved capable of supporting the rotor during continued operation at full load and speed, as well as allowing a safe rotor coastdown. The hybrid system tripled the load capacity of the magnetic bearing alone and can offer a significant reduction in total bearing weight compared to a comparable magnetic bearing.

Issue Section:
Gas Turbines: Structures and Dynamics
Keywords:
magnetic bearings, performance evaluation, gas turbines, rotors, vibration control
Topics:
Bearings, Foil bearings, Magnetic bearings, Stress, Rotors, Failure
1.
Swanson, E. E., Raju, K. V. S., and Kirk, R. G., 1996, “Test Results and Numerical Simulation of an AMB Rotor Drop,” Proc. 6th Int. Conf. on Vibrations in Rotating Machinery, I Mech Eng., UK, pp. 119–131.
2.
Ehrich
,
F. F.
,
1996
, “
The Dynamic Stability of Rotor/Stator Rubs in Rotating Machinery
,”
J. Eng. Ind.
,
90
, pp.
1025
–
1028
.
3.
Chen, H. M., Walton, J. F., and Heshmat, H., 1997, “Zero Clearance Auxiliary Bearings for Magnetic Bearing Systems,” ASME Paper No. 97-GT-112.
4.
Chen, H. M., Walton, J. F., and Heshmat, H., 1997, “Test of a Zero Clearance Auxiliary Bearing,” Proceedings of the Mag ’97 Industrial Conference and Exhibition on Magnetic Bearings, pp. 111–119.
5.
Suriano, F. J., Dayton, R. D., and Woessner, F. G., 1983, “Test Experience With Turbine-End Foil Bearing Equipped Gas Turbine Engines,” ASME Paper No. 83-GT-73.
6.
Heshmat, H., Chen, H. M., and Walton, J. F., 1998, “On the Performance of Hybrid Foil-Magnetic Bearings,” ASME Paper No. 98-GT-376.
7.
Heshmat
,
H.
,
1994
, “
Advancement in the Performance of Aerodynamic Foil Journal Bearings—High Speed and Load Capacity.
”
ASME J. Tribol.
,
116
, pp.
287
–
295
.
8.
Walton, II, J. F., and Heshmat, H., “Application of Foil Bearings to Turbomachinery Including Vertical Operation,” ASME Paper No. 99-GT-391.
9.
Heshmat
,
H.
, and
Ku
,
C.-Pr.
,
1994
, “
Structural Damping of Self-Acting Compliant Foil Journal Bearings
,”
ASME J. Tribol.
,
116
, pp.
76
–
82
.
10.
Heshmat
,
C. A.
, and
Heshmat
,
H.
,
1995
, “
An Analysis of Gas-Lubricated, Multileaf Foil Bearings with Backing Springs
,”
ASME J. Tribol.
,
117
, pp.
437
–
443
.
11.
Heshmat, H., and Hermel, P., 1992, “Compliant Foil Bearing Technology and Their Application to High-Speed Turbomachinery,” 19th Leeds-Lyon Symp., Leeds, UK.
12.
Walton, J. F., and Heshmat, H., 1994, “Compliant Foil Bearings for use in Cryogenic Turbopumps,” NASA CP3232, Vol. 1, pp. 372–381.
13.
Heshmat, H., 1999, “Operation of Foil Bearings Beyond the Bending Critical Mode,” ASME Paper No. 99-TRIB-48.
14.
Swanson, E. E., Walton, J. F., and Heshmat, H., 1999, “A 35,000 RPM Test Rig for Magnetic, Hybrid, and Back-Up Bearings,” ASME Paper No. 99-GT-180.
15.
Swanson, E. E., and Heshmat, H., 2000, “Capabilities of Large Foil Bearings,” ASME Paper 2000-GT-387.
Copyright © 2002
 by ASME
You do not currently have access to this content.