This study is devoted to providing a mechanistic rationale of coarsening induced failure in solder alloys during thermomechanical fatigue. Micromechanical modeling of cyclic deformation of eutectic tin-lead alloy was undertaken using the finite element method. The models consist of regularly arranged tin-rich and lead-rich phases, simulating the lamellar array and colony structure in a typical eutectic system. A fine structure and a coarse structure, bearing the same phase fraction but different in the aspect ratio of each lead-rich layer and in the number of lead-rich layers in each colony, are utilized for representing the microstructure before and after coarsening, respectively. Both phases are treated as elastic–plastic solids with their respective properties. For simplicity the creep effect is ignored without compromising the main objective of this study. Cyclic loading under pure shear and uniaxial conditions is modeled. It is found that both the fine and coarse structures exhibit essentially the same macroscopic stress–strain response. The coarse structure, however, shows a greater maximum effective plastic strain on a local scale throughout the deformation. The numerical result implies that, in a solder joint, a locally coarsened region may not be mechanically weaker than its surrounding, but it is subject to early damage initiation due to accumulated plasticity. Other implications regarding solder alloy failure and micromechanical modeling of two-phase materials are discussed.
Skip Nav Destination
e-mail: shenyl@me.umn.edu
Article navigation
March 2001
Technical Papers
Phase Structure and Cyclic Deformation in Eutectic Tin-Lead Alloy: A Numerical Analysis
Y.-L. Shen,
e-mail: shenyl@me.umn.edu
Y.-L. Shen
Department of Mechanical Engineering, The University of New Mexico, Albuquerque, NM 87131
Search for other works by this author on:
W. Li,
W. Li
Department of Mechanical Engineering, The University of New Mexico, Albuquerque, NM 87131
Search for other works by this author on:
H. E. Fang
H. E. Fang
Sandia National Laboratories, Albuquerque, NM 87185
Search for other works by this author on:
Y.-L. Shen
Department of Mechanical Engineering, The University of New Mexico, Albuquerque, NM 87131
e-mail: shenyl@me.umn.edu
W. Li
Department of Mechanical Engineering, The University of New Mexico, Albuquerque, NM 87131
H. E. Fang
Sandia National Laboratories, Albuquerque, NM 87185
Contributed by the Electrical and Electronic Packaging Division for publication in the JOURNAL OF ELECTRONIC PACKAGING. Manuscript received by the EEPD August 23, 1999; revised manuscript received June 29, 2000. Associate Editor: G. DeMey.
J. Electron. Packag. Mar 2001, 123(1): 74-78 (5 pages)
Published Online: June 29, 2000
Article history
Received:
August 23, 1999
Revised:
June 29, 2000
Citation
Shen, Y., Li, W., and Fang, H. E. (June 29, 2000). "Phase Structure and Cyclic Deformation in Eutectic Tin-Lead Alloy: A Numerical Analysis ." ASME. J. Electron. Packag. March 2001; 123(1): 74–78. https://doi.org/10.1115/1.1324673
Download citation file:
Get Email Alerts
Cited By
Anand Model Constants of Sn-Ag-Cu Solders: What Do They Actually Mean?
J. Electron. Packag
Enhancing Mechanical Reliability of Silver-Sintered Joints With Copper Nanowires in High-Power Electronic Devices
J. Electron. Packag (December 2024)
Special Issue on InterPACK2023
J. Electron. Packag (December 2024)
Related Articles
Low Cycle Fatigue Testing of Ball Grid Array Solder Joints under Mixed-Mode Loading Conditions
J. Electron. Packag (September,2005)
Inelastic Deformation and Fatigue of Solder Alloys Under Complicated
Load Conditions
J. Electron. Packag (June,2007)
Thermomechanical Fatigue Testing and Analysis of Solder Alloys
J. Electron. Packag (March,2000)
Creep in Shear of Experimental Solder Joints
J. Electron. Packag (June,1990)
Related Proceedings Papers
Related Chapters
Understanding the Problem
Design and Application of the Worm Gear
Subsection NB—Class 1 Components
Companion Guide to the ASME Boiler & Pressure Vessel Codes, Volume 1 Sixth Edition
Microstructure Evolution and Physics-Based Modeling
Ultrasonic Welding of Lithium-Ion Batteries