We investigated the changes of flow patterns in a blood vessel with a side wall aneurysm resulting from placement of a stent. Local hemodynamics can be markedly altered by placing an intravascular stent, which covers the orifice of the aneurysm. The alterations in flow patterns can lead to flow stasis in the aneurysmal pouch and promote the formation of a stable thrombus. Furthermore, a porous stent can serve as substrate for neointimal growth and subsequently induce a remodeling of the diseased arterial segment. To examine changes in local hemodynamics due to stent placement, a stented and nonstented aneurysm model was investigated computationally in a three-dimensional configuration using a finite element fluid dynamics program. The finite element model was studied under incompressible, pulsatile, viscous, Newtonian conditions. The fluid dynamic similarity parameter, i.e., the maximum/minimum Reynolds number, was set at about 240/25 based on cross-sectional average instantaneous flow. The Womersley number was set to 2.5. These values are representative of large cerebral arteries. The results of the stented versus the nonstented model show substantial differences in flow patterns inside the aneurysmal pouch. Flow activity inside the stented aneurysm model is significantly diminished and flow inside the parent vessel is less undulated and is directed past the orifice. A high-pressure zone at the distal neck and the dome of the aneurysm prior to stenting decreases after stent placement. However, elevated pressure values are found at the stent filaments facing the current. Higher shear rates are observed at the distal aneurysmal neck after stenting, but are confined to a smaller region and are unidirectional compared to the nonstented model.
Skip Nav Destination
Article navigation
Technical Papers
Modeling of Flow in a Straight Stented and Nonstented Side Wall Aneurysm Model
M. Aenis,
M. Aenis
Department of Mechanical and Aerospace Engineering. State University of New York at Buffalo, Buffalo, NY 14260
Search for other works by this author on:
A. P. Stancampiano,
A. P. Stancampiano
Department of Mechanical and Aerospace Engineering. State University of New York at Buffalo, Buffalo, NY 14260
Search for other works by this author on:
A. K. Wakhloo,
A. K. Wakhloo
Department of Neurosurgery. State University of New York at Buffalo, Buffalo, NY 14260
Search for other works by this author on:
B. B. Lieber
B. B. Lieber
Department of Mechanical and Aerospace Engineering; Department of Neurosurgery. State University of New York at Buffalo, Buffalo, NY 14260
Search for other works by this author on:
M. Aenis
Department of Mechanical and Aerospace Engineering. State University of New York at Buffalo, Buffalo, NY 14260
A. P. Stancampiano
Department of Mechanical and Aerospace Engineering. State University of New York at Buffalo, Buffalo, NY 14260
A. K. Wakhloo
Department of Neurosurgery. State University of New York at Buffalo, Buffalo, NY 14260
B. B. Lieber
Department of Mechanical and Aerospace Engineering; Department of Neurosurgery. State University of New York at Buffalo, Buffalo, NY 14260
J Biomech Eng. May 1997, 119(2): 206-212 (7 pages)
Published Online: May 1, 1997
Article history
Received:
December 22, 1995
Revised:
May 23, 1996
Online:
October 30, 2007
Citation
Aenis, M., Stancampiano, A. P., Wakhloo, A. K., and Lieber, B. B. (May 1, 1997). "Modeling of Flow in a Straight Stented and Nonstented Side Wall Aneurysm Model." ASME. J Biomech Eng. May 1997; 119(2): 206–212. https://doi.org/10.1115/1.2796081
Download citation file:
Get Email Alerts
Related Articles
Numerical Study of Shear-Induced Thrombus Formation Over Aterial Stent Struts
J. Med. Devices (June,2009)
Influence of the Anatomical Structure on the Hemodynamics of Iliac Vein Stenosis
J Biomech Eng (January,2023)
Impact of Stents and Flow Diverters on Hemodynamics in Idealized Aneurysm Models
J Biomech Eng (July,2011)
Finite-Element Modeling of the Hemodynamics of Stented Aneurysms
J Biomech Eng (June,2004)
Related Proceedings Papers
Related Chapters
List of Commercial Codes
Introduction to Finite Element, Boundary Element, and Meshless Methods: With Applications to Heat Transfer and Fluid Flow
PSA Level 2 — NPP Ringhals 2 (PSAM-0156)
Proceedings of the Eighth International Conference on Probabilistic Safety Assessment & Management (PSAM)
Introduction
Axial-Flow Compressors